Yamaha EK40G Скачать руководство пользователя

Страница: 61 / 200

6H95G11

5-4

Special service tools/Power unit

Power unit

Checking the compression pressure

Start the engine, warm it up for 5 min-
utes, and then turn it off.

Remove the clip from the engine stop
lanyard switch.

Remove the spark plug caps and all
spark plugs, and then install the special
service tools into a spark plug hole.

Before removing the spark plugs, blow
compressed air in the spark plug well to
clear out any dirt or dust that may fall into
the cylinder.

Fully open the throttle, and then crank the
engine until the reading on the compres-
sion gauge stabilizes.

NOTE:

Do not pull the choke knob when checking
the compression pressure.

If the compression pressure is below
specification and the compression pres-
sure for each cylinder is unbalanced, add
a small amount of engine oil to the cylin-
ders, and then check the compression
pressure again.

NOTE:

If the compression pressure increases,
check the pistons and piston rings for wear.
Replace if necessary.

If the compression pressure does not
increase, check the cylinder head gasket,
and cylinder head. Replace if necessary.

Compression gauge:

90890-03160

6F650010

Minimum compression pressure
(reference data):

400 kPa (4.0 kgf/cm

, 58 psi)

6H95G11_05 04.8.6 11:00 Page 5

Содержание EK40G









































































































































































































Результаты поиска

Содержание EK40G

Отзывы:

Похожие инструкции для EK40G

Бренды по названию

Популярные бренды

Yamaha EK40G, Руководство по обслуживанию

Результаты поиска

Содержание EK40G

Отзывы:

Похожие инструкции для EK40G

Бренды по названию

Популярные бренды