manualshive.com logo in svg

Yamaha EK40G, Руководство по обслуживанию

Поделиться
Скачать
Yamaha EK40G Скачать руководство пользователя страница 14

GEN

INFO

1-9

6H95G11

General information

Checking the engine start switch,
engine stop lanyard switch and
engine stop button

1.

Check that the engine starts when the
engine start switch is turned to START.
(remote control model)

2.

Check that the engine turns off when the
engine start switch is turned to OFF.
(remote control model)

3.

Check that the engine turns off when the
engine stop lanyard switch (and or
engine stop button) is pushed or the
engine stop lanyard is pulled from the
engine stop lanyard switch.

Checking the cooling water pilot
hole

1.

Check that cooling water is discharged
from the cooling water pilot hole.

Test run

1.

Start the engine, then check that the gear
shift operates smoothly.

2.

Check the engine idle speed after the
engine has been warmed up.

3.

Operate at trolling speed.

4.

Run the outboard motor for 1 hour at
3,000 r/min or at half throttle, then for
another hour at 4,000 r/min or at 3/4
throttle.

5.

Check that the outboard motor does not
tilt up when shifting into reverse and that
water does not flow in over the transom.

NOTE:

The test run is part of the break-in operation.

6F610130

6F610140

6F610150

6F610170

 6H95G11_01  04.7.14 21:01  Page 12

Содержание EK40G









































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды