Xylem Sontek River Surveyor RS5 Скачать руководство пользователя страница 46

Страница: 46 / 149

SonTek RS5 User Manual (August 2020) 46

Measurement

Component

Variable

Action

Message

Criteria

Boat Speed

Warning

Boat Speed is greater than 0.7m/s

0.7m/s

Bottom Track

Counter /

Warning

Samples with bad BT

Counter /

Warning

Samples with bad BT (edited)

Warning

9 Consecutive samples with bad BT

9 Samples

Warning

Discharge will be biased low

Warning

Consider restarting the measurement

using GPS reference

Cells

Warning

Number of cells less than 2

2 Cells

Edge

Warning

Too shallow to collect edge data

2 Cells

Warning

Edge Q is more than 5 percent of total

Warning

Please make sure that the start edge

bank is entered correctly

Edge (Start)

Warning

Consider moving farther away from

bank

2 Cells

Warning

Number of start edge samples is less

than 10

Samples

Edge (End)

Warning

Consider moving farther away from

bank

2 Cells

Warning

Number of start edge samples is less

than 10

Samples

Depth

Reference

Warning

BT was used as depth reference

Warning

VB was used as depth reference

Temperature

Warning

Significant change in temperature

during transect

2°C

Width

Warning

Variation in width from the previous

transect is more than 5 percent

Warning

COV of Width is greater than 5 percent

Содержание Sontek River Surveyor RS5






















































































































































Результаты поиска

Содержание Sontek River Surveyor RS5

Отзывы:

Похожие инструкции для Sontek River Surveyor RS5

Бренды по названию

Популярные бренды

Xylem Sontek River Surveyor RS5, Руководство пользователя

Результаты поиска

Содержание Sontek River Surveyor RS5

Отзывы:

Похожие инструкции для Sontek River Surveyor RS5

Бренды по названию

Популярные бренды