Xylem Sontek River Surveyor RS5 Скачать руководство пользователя страница 138

Страница: 138 / 149

SonTek RS5 User Manual (August 2020) 138

C-4.

Terminal Emulator

The RSQ software provides a terminal emulator interface for advanced users who have

been in contact with SonTek Technical Support and have received special instructions

for issuing terminal commands. The terminal emulator interface is shown below:

C-5.

Firmware Upgrade

The Firmware Upgrade button allows the user to load new firmware onto the RS5.

Please ensure that before performing a firmware upgrade, there is sufficient battery life

in the RS5. A low battery could cause communications drops and jeopardize the

firmware upgrade process.

When the Firmware Upgrade button is pressed, the following dialog will appear:

Содержание Sontek River Surveyor RS5






















































































































































Результаты поиска

Содержание Sontek River Surveyor RS5

Отзывы:

Похожие инструкции для Sontek River Surveyor RS5

Бренды по названию

Популярные бренды

Xylem Sontek River Surveyor RS5, Руководство пользователя

Результаты поиска

Содержание Sontek River Surveyor RS5

Отзывы:

Похожие инструкции для Sontek River Surveyor RS5

Бренды по названию

Популярные бренды