Xylem Sontek River Surveyor RS5 Скачать руководство пользователя страница 63

Страница: 63 / 149

SonTek RS5 User Manual (August 2020) 63

(

[email protected]

) before using this option. This can be done through the Repair

Device Without Firmware feature from the Connect dialog, highlighted in Figure 35.

Figure 35. Repair Device Without Firmware

The Repair Device Without Firmware dialog (Figure 36) will prompt the user for the

instrument serial number and the firmware file the user wishes to use. Please select the

appropriate file and click

Figure 36. Repair Device Without Firmware Dialog

The software will prompt the user to power cycle the RS5 system. Be sure to click

Continue

before powering on the system.

Figure 37. Repair Device Without Firmware Prompt to Power Cycle

The new firmware will then be loaded onto the system.

Содержание Sontek River Surveyor RS5






















































































































































Результаты поиска

Содержание Sontek River Surveyor RS5

Отзывы:

Похожие инструкции для Sontek River Surveyor RS5

Бренды по названию

Популярные бренды

Xylem Sontek River Surveyor RS5, Руководство пользователя

Результаты поиска

Содержание Sontek River Surveyor RS5

Отзывы:

Похожие инструкции для Sontek River Surveyor RS5

Бренды по названию

Популярные бренды