Xtreme X90-2S Скачать руководство пользователя страница 64

Страница: 64 / 88

⚫

+10%

⚫

+15%

⚫

+20% (Default)

Lower limit

⚫

-10%

⚫

-20%

⚫

-30% (Default)

Bypass Frequency
Range

Set bypass Frequency range:
Upper/ Lower limit

⚫

+/- 1Hz

⚫

+/- 2Hz

⚫

+/- 4Hz (Default)

Converter
Mode

Set converter mode

⚫

Disable (Default)

⚫

Enable

⚫

50Hz

⚫

60Hz

⚫

AUTO

ECO Mode

Set ECO mode

⚫

Disable (Default)

⚫

Enable

Bypass
Mode

Set bypass mode

⚫

Disable

⚫

Enable (Default)

MUST be reviewed after UPS installation.

If you need the UPS to power the load when the inverter
is OFF, this setting must be set to

“

Enable

”

Auto-Restart --

Set auto-restart

⚫

Disable

⚫

Enable (Default)

If set to

“Enable”

, the UPS will enter line mode once

utility restores after the UPS has shut down upon full

battery discharge.

Power Walk
in

Set power walk in upper/lower limits

⚫

+/- 1s time step (setting range: 1s ~ 10s)

Battery
Mode Delay
Time

Set system shutdown delay time in battery mode
(0~990min).

⚫

0: Disable (Default)

⚫

Not 0: Enable

If set to

“

Enable

”

, UPS will shut off output after UPS

operates in Battery mode for the preset number of
minutes.

Shutdown/
Restore

System Shutdown

Time

Set system shutdown delay time (0.2~99min)

⚫

0.2 min (Default)

The delay timer will start counting when the
CONTROL-Shutdown Restore command is executed.

System Restore Time Set system restore time (0~9999min)

⚫

1 min (Default)

Содержание X90-2S
























































































Результаты поиска

Содержание X90-2S

Отзывы:

Похожие инструкции для X90-2S

Бренды по названию

Популярные бренды

Xtreme X90-2S, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание X90-2S

Отзывы:

Похожие инструкции для X90-2S

Бренды по названию

Популярные бренды