Xtreme X90-2S Скачать руководство пользователя страница 35

Страница: 35 / 88

3.3 UPS Operation

⚫

Do not start the UPS until the installation is completed.

⚫

Make sure the wiring is correct and the power cables are fixed firmly.

⚫

Make su

re the Power Modules’ address

IDs have been configured. Refer to section 2.9.2

⚫

Make sure the ready switch on the Power Module has been switched

to the “Locked”

position.

⚫

Make sure all the breakers are switched

OFF

3.3.1 AC Startup

Ensure to follow this procedure when turning on the UPS from a fully powered-down state.
The operating procedures are:

Step 1

: Refer to

“

Chapter 2 Installation

”

to connect the power cables and install the Power

Modules and the battery required for the UPS system.

Step 2

: Switch ON the battery breaker.

Step 3

: Switch ON the external power switch in a distribution panel to power the UPS.

Содержание X90-2S
























































































Результаты поиска

Содержание X90-2S

Отзывы:

Похожие инструкции для X90-2S

Бренды по названию

Популярные бренды

Xtreme X90-2S, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание X90-2S

Отзывы:

Похожие инструкции для X90-2S

Бренды по названию

Популярные бренды