48
XDSR600HD
such as dual recording.
This connection is used when
the
TUNER 1
is connected
with LNB output, and the Loop-
through output of the
TUNER
1
is connected with input of the
TUNER 2.
This is the way to
use & activate both tuners when
you have only 1 LNB with your
dish antenna. However, this will
limit the possible tuning range
(Satellite & Polarization) of the
2nd tuner, while the 1st tuner
is being used for its recording
process (Because the input signal
of 2nd tuner is dependent of
the signal which the 1st tuner is
tuned to).
NOTE
: User should make
the appropriate connection
by choosing the right tuner
connections between the
Loop-Through and Separate
connections. Due to the
difference of these two
connections, wrong LNB and
Tuner connection may cause
the loss of signal reception. We
strongly recommend the use of
Tuner Connection:
You can set
connection type, Separate or
Loop-Through.
NOTE
: Tuner Connection menu is
disabled if tuner is not connected
in twin satellite or only one tuner
is connected.
Separate:
Set the connection type
option to
‘Separate’
, if each of
the tuners are connected to
different LNBs (TUNER 1 / TUNER
2) individually / independently.
This Separate connection is
used, when each two tuners are
connected to different LNBs.
Due the independent & separate
connections between two Tuners
& LNBs, user can watch all the
services scanned by one
TUNER
1
, while the other
TUNER 2
is set
for recording at the same time.
Loop-Through:
Set the connection
type option to
‘Loop-Through’
, if
you have connected the LNB OUT
(TUNER 1) and LNB IN (TUNER
2) with a loop-through cable. In
this case, you would have some
limitations in using some features
3.1. Dish Setting
Select the satellite/antenna
and LNB settings for service
search. The values that are set
in this menu will be available
for selection in other service
searching menus.
Satellite:
Select the satellite which you
want to do a search for.
- Press the
LEFT/RIGHT ARROW
button to select the satellite.
- If you press the
OK
button, the
entire satellite list will be displayed.
- Select the desired satellite name
to search.
- If the desired satellite name is not
listed then select User Defined.
professional service personnel
to make this installation and
connection if your knowledge is
limited.
Tuner:
Select the tuner which
you want to set (Tuner 1/ Tuner
2). If you set
‘Loop-Through’
on the menu
(Installation-Dish
Setting-Tuner Connection),
this
menu(Tuner) will be disabled
automatically.
Frequency:
Select the satellite
frequency which you want to use
for checking the signal.
LNB Power:
Select the LNB
power on or off.
LNB Type:
Select the LNB type.
LNB Frequency:
Select the local
oscillator (L.O.). frequency that is
specified for the LNB used.
Use the
LEFT/RIGHT ARROW
buttons to select the LNB
frequency.
If the required LNB frequency
is not listed, then enter the
www.xcruiser.net
www.xcruiser.net
XDSR600HD
XDSR600HD
with LNB output, and the Loop-
with LNB output, and the Loop-
TUNER
TUNER
is connected with input of the
is connected with input of the
This is the way to
This is the way to
use & activate both tuners when
use & activate both tuners when
you have only 1 LNB with your
you have only 1 LNB with your
dish antenna. However, this will
dish antenna. However, this will
limit the possible tuning range
limit the possible tuning range
(Satellite & Polarization) of the
(Satellite & Polarization) of the
2nd tuner, while the 1st tuner
2nd tuner, while the 1st tuner
is being used for its recording
is being used for its recording
process (
process (
B
B
ecause the input signal
ecause the input signal
of 2nd tuner is dependent of
of 2nd tuner is dependent of
the signal which the 1st tuner is
the signal which the 1st tuner is
TUNER
TUNER
2) individually / independently.
2) individually / independently.
This Separate connection is
This Separate connection is
used, when each two tuners are
used, when each two tuners are
connected to different LNBs.
connected to different LNBs.
Due the independent & separate
Due the independent & separate
connections between two Tuners
connections between two Tuners
& LNBs, user can watch all the
& LNBs, user can watch all the
services scanned by one
services scanned by one
TUNER
TUNER
1
1
, while the other
, while the other
TUNER 2
TUNER 2
for recording at the same time.
for recording at the same time.
Loop-Through:
Loop-Through:
type option to
type option to
you have connected the LNB OUT
you have connected the LNB OUT
LEFT/RIGHT ARROW
LEFT/RIGHT ARROW
button to select the satellite.
button to select the satellite.
If you press the
If you press the
OK
OK
button, the
button, the
OK
OK
OK
entire satellite list will be displayed.
entire satellite list will be displayed.
-
-
Select the desired satellite name
Select the desired satellite name
to search.
to search.
-
-
If the desired satellite name is not
If the desired satellite name is not
listed then select User Defined.
listed then select User Defined.
professional service personnel
professional service personnel
to make this installation and
to make this installation and
connection if your knowledge is
connection if your knowledge is
limited.
limited.
Tuner:
Tuner:
Select the tuner which
Select the tuner which
you want to set (Tuner 1/ Tuner
you want to set (Tuner 1/ Tuner
2). If you set
2). If you set
on the menu
on the menu
Setting-Tuner Connection),
Setting-Tuner Connection),
