WorldViz PPT-E Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 163

WorldViz PPT-E Скачать руководство пользователя страница 145

Support

139

Edit Serial Numbers:

Use this to reconfigure the serial numbers of your system's cameras. The serial
numbers are 5 characters long (A-Z, 0-9) and must match exactly the order of the
digitizers on the back of the computer, and the cabling to the cameras.

PPT-E

Use this plugin to configure the PPT-E cameras. The options available for
configuration are:

Vertical blanking:

The amount of time the camera will wait before capturing the next frame.
Minimum value of 4 corresponds to 10.2 microseconds and the cameras will run at
196 frames per second.
If you are using PPT-H marker id units with PPT-E, then you should set this option to
47, and the cameras will run at 180 frames per second.

Shutter time:

The amount of time to capture light with the sensor before processing it.
4960 microseconds is the maximum value, and also the recommended value for
most tracking scenarios.
Smaller values should be used to minimize motion blur with very fast objects.
If you check the box "disable synchronization" then this allows much larger shutter
times, but synchronization is disabled. Typically this checkbox should always be
cleared and the shutter time set to 4960 microseconds.

Brightness shift:

Apply an additive brightness shift to your PPT camera capture images.
Range from -255 to 255, 0 is the recommended default which applies no offset.

Sensor gain:

Adjust the gain applied within the camera sensor.
The recommended value for PPT-E is 4, which is the default sensor gain.
Adjusting this value may lead to unexpected side-effects, and should typically not be
adjusted.

Broadcast address:

The address to use when scanning for cameras on your local network. This will
typically be 255.255.255.255 for an automatic scan of all available network
interfaces. If you have multiple PPT-E configurations on separate networks, you will
need to specify this exactly.

History length and velocity threshold:

The two parameters are preset to WorldViz recommended values that prevent static
tracking from jittering.

«
...
143
144
145
146
147
...
»

Содержание PPT-E




































































































































































Отзывы:

Нет отзывов