Wohler iAM2-8 Скачать руководство пользователя страница 82

Страница: 82 / 116

Page 82

Updating Multiple Units Remotely

Use the following steps to update one or more iAM2-8 units remotely by
transferring the software from a previously updated iAM2-8:

If any of the iAM2-8 units that you intend to update remotely may be in use,
contact the people using them and let them know what you will be doing.
The iAM2-8

units being updated will be temporarily out of service.

Use the Wohler Web GUI to connect to an iAM2-8 already containing the
latest update. This will be referred to as the

Master Unit

. Navigate to the

System | System Update | Remote System Update

menu. The screen

shown in Figure A-12 will appear and the Web GUI will scan the network for
any active iAM2-8 units.

Figure A-12 – Scanning for iAM2-8 Units

Note:

The scanning process will take 2 minutes. Progress is shown on the

screen. If for some reason you would like to stop the scan prematurely, click the

Stop Scan

button.

Important:

Do not

run the scanning or updating process from

more than one

Master Unit

at a time, to avoid problems. Although you may be updating

multiple units at the same time, never attempt this process from more than one

Master Unit

When the scanning is complete, a list of found iAM2-8 units will be shown as
in Figure A-13. Click either

Select All

or click only the

Target

units that you

want to update.

Содержание iAM2-8





















































































































Результаты поиска

Содержание iAM2-8

Отзывы:

Похожие инструкции для iAM2-8

Бренды по названию

Популярные бренды

Wohler iAM2-8, Руководство пользователя

Результаты поиска

Содержание iAM2-8

Отзывы:

Похожие инструкции для iAM2-8

Бренды по названию

Популярные бренды