Wohler iAM2-8 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 116

background image

Page 10

amplifiers. There are two (left/right) speakers. The speaker response may be
adjusted with tone controls in the

Speaker Options

menu. Refer to the

Menu /

Option Touchscreen

section of Chapter 2.

4.

Headphone Jack

:

A 1/4" jack for an optional headphone is provided on the front

panel. Speaker audio can be optioned to either mute or not mute when
headphones are plugged in. This is set in the

Speaker Options

menu. If the

speaker audio is set to mute with headphone insertion, and a headphone is plugged
into the Headphone Jack, the following icon will appear near the center top of the

Meter Screen:

5.

Volume

:

This controls the speakers, the headphone, and the analog outputs. As

the

Volume

control is turned, a graphic appears at the center top of the Meter

Screen, as follows:

Pressing the

Volume

control mutes the audio and a speaker muted icon appears

near the center top the Meter Screen:

This icon also displays whenever the

Volume

control is turned all the way counterclockwise.

6.

Balance

:

This

controls the relative left/right levels for the monitored stereo mix.

Pressing the knob will bring the balance back to center. It controls the speakers,
the headphone, and the analog outputs. As the

Balance

control is turned, a

graphic appears at the center top of the Meter Screen as follows:

7.

Source

: Turning this control right or left selects between the available licensed

input sources. The selected Source input is displayed in the center of the Audio

Meters Screen as follows:

Alternatively, the

Source

control can be used to select from any Preset, or from

any Favorite Preset. Refer to the

Source Knob Select

setting in the

Unit Config

menu. Regardless of this menu setting, when the Loudness Meter Screen is
displayed, the

Source

knob selects which Loudness Cluster is to be measured and

monitored.

8.

Channel

: Turning this control moves a white selection box from channel to channel

on the metering screen. Press the control to solo the highlighted channel. The box
will turn blue and any other boxes will disappear. To remove the solo and return to
the previous monitoring configuration, press the

Channel

control once again.

9.

USB

: This USB 2.0 Type A connector allows you to use a flash drive (not supplied)

to perform software updates and copy system configurations to another

iAM2-8

or

to a PC. Refer to Appendix A of this manual to learn about performing a software
update.

10.

Status

: This indicator lights green when the system is powered and ready for use.

A solid or blinking yellow color indicates that the product is starting up. A red color
indicates that a system update is taking place. Refer to Appendix A for procedures
to update software.

«
...
8
9
10
11
12
...
»

Содержание iAM2-8





















































































































Отзывы:

Нет отзывов

Похожие инструкции для iAM2-8

Бренд: Farfisa Страницы: 72

Бренд: Abicor Binzel Страницы: 42

Бренд: jablotron Страницы: 17

Бренд: Mach Страницы: 2

Бренд: Nelson Страницы: 18

Бренд: Nelson Страницы: 150

Water Jet Lightning

Бренд: Oase Страницы: 28

Бренд: Oase Страницы: 9

Бренд: Q Acoustics Страницы: 8

Бренд: Q Acoustics Страницы: 19

Бренд: Safeline Страницы: 76

Бренд: Valcom Страницы: 1

Бренд: Valcom Страницы: 1

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 3

Бренд: Nady Audio Страницы: 2

Бренд: Q-See Страницы: 9

Бренд: Black Widow Security Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды