background image

31

CapaCiTiES

 

aNd

 

raTiNgS

A.  Ceiling Capacity ............................................................100 lb./sq.ft.

B.  Power Requirements

 

The recommendation for power connections to V-Room Practice is that each room 

 

must have one dedicated 20A circuit.

 

Light Fixture

 

One 8" Fixture...............................................................1.1A

 

One 4' Fixture ................................................................0.6A

 

 

Fan (each) ....................................................................1.9A

 

Electronic System (V-Room Practice only) ..................1.0A @ 120V AC 60 Hz

 

Inrush Current ...............................................................20A maximum for 2 milliseconds.

 

Time to Steady State ....................................................10 milliseconds.

 

Interior outlets, maximum amperage per power panel available is 10 amps.

C.  Floor Load Capacity
 

Distributed Load ...........................................................200 lb./sq.ft.

 

Concentrated Load .......................................................300 lb./sq.ft.

D.  Glass Specs: (CPSC Standard No. 1201 Category II) Covered by Federal Spec. DD-G-451C

 

Inner Pane: 3/16"x24 15/16"x76 7/8" Laminated Safety Glass with .030 Plastic.

 

Outer Pane: 1/4"x24 15/16"x76 7/8" Laminated Safety Glass with .030 Plastic.

Содержание V-Ready





































Отзывы: