weinor Terrazza Originale Скачать руководство пользователя страница 74

Страница: 74 / 104

Terrazza Originale

Instructions for assembly

Version 5

12.06.2017

We reserve the right to make technical changes

Item number

111361-0000

Page 74/104

5.2.3 Installing the gutter corner and two 180° posts in the corner

Figure: Installing the roof gutter corner on the post

Corner connector

Gutter connector



Assemble the first section of guttering and the posts.



Apply a suitable adhesive and sealant to the guttering and corner connector.



Insert the corner connector into the pre-assembled guttering.



Affix the 90° gutter connector using a suitable adhesive and sealant.



Apply a suitable adhesive and sealant to the mitred part of the second section of guttering.



Apply a suitable adhesive and sealant to protruding section of the corner connector.



Slide the second section of guttering over the corner connector and insert the kinked

threaded rods used for tensioning into the support angles.



Attach the guttering to the posts.



Remove any excess adhesive and sealant.



Tension the two sections of guttering using the kinked threaded rods and tighten the nuts.

Ø 8

M8x50

Ø 6

Содержание Terrazza Originale









































































































Результаты поиска

Содержание Terrazza Originale

Отзывы:

Похожие инструкции для Terrazza Originale

Бренды по названию

Популярные бренды

weinor Terrazza Originale, Инструкция по сборке

Результаты поиска

Содержание Terrazza Originale

Отзывы:

Похожие инструкции для Terrazza Originale

Бренды по названию

Популярные бренды