weinor Terrazza Originale Скачать руководство пользователя страница 35

Страница: 35 / 104

Terrazza Originale

Instructions for assembly

Version 5

12.06.2017

We reserve the right to make technical changes

Item number

111361-0000

Page 35/104

3.11 Installation on a side wall



If the roof abuts against a wall at one side, the gutter cover plate will need to be screwed onto

the gutter before fitting the gutter with posts.



Before the roof support can be fitted, the wall cover plate will need to be screwed onto the roof

support and sealed along the side of the roof support.



Once the roof support and the side wall bracket have been fitted, the roof support and guttering

will need to be sealed along the side facing the wall.



Trim the profiles on-site where the side wall bracket and the wall bracket meet at the rear wall.

Figure: Installation on a side wall

25 Screwing the plate to the roof support prior to fitting the roof support

4.2x16

Содержание Terrazza Originale









































































































Результаты поиска

Содержание Terrazza Originale

Отзывы:

Похожие инструкции для Terrazza Originale

Бренды по названию

Популярные бренды

weinor Terrazza Originale, Инструкция по сборке

Результаты поиска

Содержание Terrazza Originale

Отзывы:

Похожие инструкции для Terrazza Originale

Бренды по названию

Популярные бренды