weinor Terrazza Originale Скачать руководство пользователя страница 60

Страница: 60 / 104

Terrazza Originale

Instructions for assembly

Version 5

12.06.2017

We reserve the right to make technical changes

Item number

111361-0000

Page 60/104

5.1.3 Fitting the 135° post



Saw the post to length.



Align the post to the side roof support and trace the outline of the post on the floor.



Using the traced outline, bring the 90x70x7x28 angle bracket into position and affix to the

floor.



Position the 135° post over the 90x70x7x28 angle bracket and below the side roof support.



Drill into the 135° post and 90x70x7x28 angle bracket and affix (Make sure that you do not

drill into the slotted holes on the angle bracket.).



Drill through the side roof support into both 40x40x5x20 angle brackets and affix; apply

sealant to the screws.

Figure: Fitting the 135° post



Attach D12x7 protective caps to all screws that remain visible.

Angle bracket 40x40x5x20

Angle bracket 90x70x7x28

Cover cap D12x7

4.2x16

Содержание Terrazza Originale









































































































Результаты поиска

Содержание Terrazza Originale

Отзывы:

Похожие инструкции для Terrazza Originale

Бренды по названию

Популярные бренды

weinor Terrazza Originale, Инструкция по сборке

Результаты поиска

Содержание Terrazza Originale

Отзывы:

Похожие инструкции для Terrazza Originale

Бренды по названию

Популярные бренды