Watts PVi CEN 1600 Скачать руководство пользователя страница 85

Страница: 85 / 124

OMM-0153_E

• 5/11/2023 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 85 of 124

CENTURION Installation, Operation & Maintenance Manual

SECTION 8: WATER HEATER MANAGEMENT

5. Go to:

Advanced Setup

→

WHM Cascade

→

Operating Controls

→

Sequencing

Control

. The

Next On Valve Pos

parameter specifies the valve position that will trigger the

next unit to come on line, and the

Next Off Valve Pos

parameter specifies the valve

position that will trigger the next unit go off-line.

6. The Controller includes a

Setback

option, which can be used to adjust the setpoint

temperature, start and end time, for operation during periods of low demand. To specify the
setback time and temperature, go to:

Main Menu

→

Advanced Setup

→

Performance

→

Temperature Control

→

Setpoint Range

and configure the following parameters:

a. Set the

Setpoint Limiting

parameter to

Enabled

b. Configure

Setpoint Low Limit

and

Setpoint High Limit

parameters to determine

the temperature range within which the setpoint can vary. You can also configure the

Setpoint Limit

parameter, which allows you to set the number of degrees

below

Setpoint High Limit

the unit’s outlet temperature must fall before restart. Enable

Setpoint Limiting

and then configure the

Setpoint Limit Band.

7. If you want to change the Lead/Lag Hours,

go to

Advanced Setup

→

WHM Cascade

→

Operating Controls

→

Lead/Lag

, set

Lead/Lag Settings

Select Lead/Lag

, then select

the Lead and Lag units in the

Lead Unit

and

Lag Unit

fields.

8.8.2 WHM Client Configuration & Start-Up Procedure

Complete the instructions below on all units designated as WHM Clients.

1. Go to:

Advanced Setup

→

WHM Cascade

→

Cascade Configuration

and set the

WHM

Unit Mode

WHM Client

2. Go to:

Advanced Setup

→

WHM Cascade

→

Cascade Comm

Enter the Client unit’s address in the

Unit Address

parameter,

4. Set the communication parameters in the

Cascade Baud Rate

Network Timeout

and

Error Threshold

parameters.

5. Specify the

Unit Failsafe Mode

, which determines what happens if a WHM Client units

loses communication with the WHM Manager.

6. If you want to change the Lead/Lag Hours, go to:

Advanced Setup

→

WHM Cascade

→

Operating Controls

→

Lead/Lag

, set

Lead/Lag Settings

Select Lead/Lag

, then select

the Lead and Lag units in the

Lead Unit

and

Lag Unit

fields.

Содержание PVi CEN 1600





























































































































Результаты поиска

Содержание PVi CEN 1600

Отзывы:

Похожие инструкции для PVi CEN 1600

Бренды по названию

Популярные бренды

Watts PVi CEN 1600, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание PVi CEN 1600

Отзывы:

Похожие инструкции для PVi CEN 1600

Бренды по названию

Популярные бренды