Watts PVi CEN 1600 Скачать руководство пользователя страница 3

Страница: 3 / 124

OMM-0153_E

• 5/11/2023 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 3 of 124

CENTURION Installation, Operation & Maintenance Manual

5.3 COMBUSTION CALIBRATION ...........................................................................................42

5.4 OVER-TEMPERATURE LIMIT SWITCHES ........................................................................47

5.5 TEMPERATURE CONTROL CALIBRATION ......................................................................49

5.6 MODES OF OPERATION ...................................................................................................51

SECTION 6: SAFETY DEVICE TESTING ........................................................................................53

6.1 TESTING SAFETY DEVICES .............................................................................................53

6.2 LOW GAS PRESSURE TEST .............................................................................................54

6.3 HIGH GAS PRESSURE TEST ............................................................................................55

6.4 LOW WATER LEVEL FAULT TEST ....................................................................................56

6.5 WATER TEMPERATURE FAULT TEST .............................................................................57

6.6 INTERLOCK TESTS ...........................................................................................................58

6.7 FLAME FAULT TEST ..........................................................................................................58

6.8 AIR FLOW FAULT TESTS-BLOWER PROOF & BLOCKED INLET SWITCHES ................59

6.9 SSOV PROOF OF CLOSURE SWITCH CHECK ................................................................61

6.10 PURGE SWITCH OPEN DURING PURGE .......................................................................61

6.11 CHECK IGNITION SWITCH OPEN DURING IGNITION ...................................................62

6.12 SAFETY PRESSURE RELIEF VALVE TEST ....................................................................63

SECTION 7: MAINTENANCE ......................................................................................................64

7.1 MAINTENANCE SCHEDULE ..............................................................................................64

7.2 IGNITER-INJECTOR ..........................................................................................................65

7.3 FLAME DETECTOR ...........................................................................................................66

7.4 O

SENSOR MAINTENANCE .............................................................................................66

7.5 SAFETY DEVICE TESTING................................................................................................67

7.6 BURNER INSPECTION ......................................................................................................67

7.7 CONDENSATE DRAIN TRAP .............................................................................................67

7.8 AIR FILTER CLEANING AND REPLACEMENT ..................................................................68

7.9 SHUTTING WATER HEATER DOWN FOR EXTENDED PERIOD (ONE YEAR OR MORE)

7.10 RECOMMENDED PERIODIC TESTING ...........................................................................69

7.11 RECOMMENDED SPARE PARTS....................................................................................70

SECTION 8: WATER HEATER MANAGEMENT ...........................................................................71

8.1 GENERAL DESCRIPTION ..................................................................................................71

8.2 WHM PRINCIPLES OF OPERATION .................................................................................72

8.3 WHM FEATURES ...............................................................................................................72

Содержание PVi CEN 1600





























































































































Результаты поиска

Содержание PVi CEN 1600

Отзывы:

Похожие инструкции для PVi CEN 1600

Бренды по названию

Популярные бренды

Watts PVi CEN 1600, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание PVi CEN 1600

Отзывы:

Похожие инструкции для PVi CEN 1600

Бренды по названию

Популярные бренды