Watts PVi CEN 1600 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 124

background image

OMM-0153_E

• 5/11/2023 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 42 of 124

CENTURION Installation, Operation & Maintenance Manual

SECTION 5: INITIAL START-UP

5.2.3 Accessing The Analyzer Probe Port

1.

Remove the 1/4” NPT plug from the exhaust manifold.

2. If necessary, adjust the stop on the combustion analyzer probe so it will extend mid-way

into the flue gas flow.

DO NOT install the probe at this time.

Figure 5-3: Analyzer Probe Port Location

5.2.4 Recommendations For WHM Operation

It is strongly recommended that installations with multiple

Centurion units operate in Water

Heater Management (WHM) mode (see Section 2.13 for instructions on installing the actuator-
controlled Sequencing Isolation Valve). This is to ensure the system flow is divided between
units as demand increases, and that all units receive equal run time and additional Water
Heaters are activated based on the

Next On

Valve Pos

firing rate setting.

In case of pre-heated DHW systems with multiple Centurion units, it is recommended to lower
the

Next On

Valve Pos

setting to 30-40% (Default=50%), so subsequent Water Heaters are

engaged sooner to provide rapid response and divide the system flow over additional units. In
case of DHW pre-heat systems, the required temperature rise through an individual unit can be
much lower to ensure flow per unit does not exceed 50 gal. (189 L) per minute.

5.3 Combustion Calibration

Centurion Water Heaters are set up for either Natural Gas or Propane gas, as specified by the
Style Number on the Sales Order, and if applicable calibrated for Standard NOx emissions (<20
ppm) before shipping.

Recalibration as part of initial start-up is necessary due to changes in the local altitude, gas BTU
content, gas supply piping and supply regulators. Combustion Calibration Test Data sheets,
shipped with each unit, must be filled out and returned to PVI for proper Warranty Validation. It
is important to perform the combustion calibration procedure below to provide optimum
performance and keep readjustments to a minimum.

COLD WATER INLET

CONDENSATE DRAIN

DRAIN VALVE

BUILDING
RECIRCULATION
WATER INLET

ANALYZER

PROBE PORT

«
...
40
41
42
43
44
...
»

Содержание PVi CEN 1600





























































































































Отзывы:

Нет отзывов

Похожие инструкции для PVi CEN 1600

Бренд: EBARA Страницы: 22

Бренд: VARISCO Страницы: 72

Бренд: DAB Страницы: 40

Бренд: A.O. Smith Страницы: 44

Бренд: Gude Страницы: 64

Бренд: Stübbe Страницы: 32

Sanitizer Plus ASP1-1044

Бренд: Water Right Страницы: 30

Бренд: Gardenline Страницы: 28

POWERplus POWX1700

Бренд: VARO Страницы: 10

Бренд: Leader Pumps Страницы: 8

Бренд: Quality Water Treatment Страницы: 9

Бренд: Ocean Technologies Страницы: 2

Бренд: Elkay Страницы: 2

Бренд: Soleus Air Страницы: 7

Бренд: Barnes Страницы: 16

MORRIS MPH-20041S

Бренд: TUYA Страницы: 11

Бренд: S&P Страницы: 30

Бренд: Elkay Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды