Watts PVi CEN 1600 Скачать руководство пользователя страница 61

Страница: 61 / 124

OMM-0153_E

• 5/11/2023 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 61 of 124

CENTURION Installation, Operation & Maintenance Manual

SECTION 6: SAFETY DEVICE TESTING

6. When the Controller gets into the ignition phase, it will show

Ignition Trial

. At that point

attach the alligator clip (Figure 6-9) to any bare metal surface or ground. The Controller
displays

Flame Proven

and begins to ramp up to 100% fire rate. Note that no gas or

flame is present in the Water Heater at this time.

7. Wait for the unit to ramp up to at least 90% before continuing.

8. Cover the combustion air inlet opening with a solid, flat object, such as a piece of thick

plywood or a thick metal plate.

9. The unit should shut down and display

Airflow Fault During Run

. This step confirms

proper operation of the Blocked Inlet switch.

10. Remove cover from air inlet opening and reinstall the Combustion Air Duct or air filter.

11. Remove jumper wires installed in step 3 and replace the black connector boot on the

Flame Detector.

12. Press the

CLEAR

button. The unit should restart.

6.9 SSOV Proof of Closure Switch Check

The SSOV (shown in Figure 6-7) contains the

Proof of Closure

switch. The

Proof of Closure

switch circuit is checked as follows:

Set the Controller’s

Enable/Disable

switch to

Disable

2. Go to

Main Menu

→

Diagnostics

→

Manual Run

and enable

Manual Mode

3. Set the valve position

between 25% and 30%

using the

(Plus) and

–

(Minus) controls.

4. Loosen the SSOV cover screw and remove cover to access wiring connections.

5. Disconnect wire #1304

from the SSOV to “open” the Proof of Closure switch circuit.

6. The unit should fault and display

SSOV Switch Open

7. Replace wire #1304 and press the

CLEAR

button.

8. Set the

Controller’s

Enable/Disable

switch to

Enable

to start the unit.

9. Remove the wire again when the unit reaches the purge cycle and

Purging

is displayed.

10. The unit should shut down and display

SSOV Fault During Purge

11. Replace the wire on the SSOV and press the

CLEAR

button. The unit should restart.

6.10 Purge Switch Open During Purge

The

Purge

switch (and

Ignition

switch) is located on the Air/Fuel Valve. To check the switch:

Set the Controller’s

Enable/Disable

switch to

Disable

2. Go to

Main Menu

→

Diagnostics

→

Manual Run

and enable

Manual Mode

3. Set the valve position

between 25% and 30%

using the

(Plus) and

–

(Minus) controls.

4. Remove the Air/Fuel Valve cover by rotating the cover counterclockwise to unlock it.

5. Remove one of the two wires (#1609 or #1610) from the Purge switch (Figure 6-11).

Set the Controller’s

Enable/Disable

switch to

Enable

to start the unit.

7. The unit should begin its start sequence, then shut down and display

Prg Switch Open

During Purge

8. Replace wire on the Ignition switch and press

CLEAR

button. The unit should restart.

Содержание PVi CEN 1600





























































































































Результаты поиска

Содержание PVi CEN 1600

Отзывы:

Похожие инструкции для PVi CEN 1600

Бренды по названию

Популярные бренды

Watts PVi CEN 1600, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание PVi CEN 1600

Отзывы:

Похожие инструкции для PVi CEN 1600

Бренды по названию

Популярные бренды