Watts PVi CEN 1600 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 124

background image

OMM-0153_E

• 5/11/2023 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 49 of 124

CENTURION Installation, Operation & Maintenance Manual

SECTION 5: INITIAL START-UP

5.4.3 Changing The Readout Between Fahrenheit and Celsius

1. Press and hold both the

Increase

and

Decrease

arrows

at the same time for about 4

seconds. The display shows the temperature in Celsius and

°F

changes to

°C

.

2. To change the display back to Fahrenheit, repeat step 1.

Figure 5-11: Changing the Display to Celsius

5.5 Temperature Control Calibration

W A R N I N G !

Ignoring this commissioning step may cause water temperature faults, poor water
temperature control, and rapid cycling of the unit.

The unit normally comes factory set and calibrated for a 130°F (54.4°C) setpoint (default value).
However, if a different setpoint temperature is desired, use the procedure in the next section.
Temperature control calibration should be performed each time the setpoint is changed.

There are two primary adjustments for performing temperature calibration:

Min Load Adj

and

Max Load Adj

(minimum and maximum load adjustment). Adjustments to these settings are

made at minimum and maximum load conditions and should be made in small increments, from
1 to 3 degrees F (0.55 to 1.65 degrees C). After adjustment the outlet water temperature must
be allowed to settle for several minutes prior to making any further adjustments.

Temperature control calibration is accomplished by first performing the procedure in Section
5.5.2

Minimum Load Adjustment

. Once complete, perform the procedure in Section 5.5.3

Maximum Load Adjustment

.

5.5.1 Setting Outlet Water Temperature Setpoint

If the setpoint is already set to the correct values for the site skip this step and proceed to 5.5.2.

Setting Outlet Temperature Setpoint

– WHM Manager Units:

1. On the WHM Manager unit go to

Advanced Setup

→

WHM Cascade

→

Application

Configuration

.

2. Set the

Setpoint

parameter to the desired setpoint.

INCREASE

DECREASE

«
...
47
48
49
50
51
...
»

Содержание PVi CEN 1600





























































































































Отзывы:

Нет отзывов

Похожие инструкции для PVi CEN 1600

Бренд: Garantia Страницы: 2

Бренд: EasyPro Страницы: 4

Бренд: Gardena Страницы: 17

Бренд: A.O. Smith Страницы: 6

Бренд: Dimplex Страницы: 4

TURBO EXCEL SO9070

Бренд: Rowenta Страницы: 44

Бренд: P.Lindberg Страницы: 54

RainStation RS-0001

Бренд: EarthMinded Страницы: 16

Бренд: Pattfield Ergo Tools Страницы: 162

Бренд: Fenix Страницы: 12

Бренд: Saab Страницы: 40

TriScroll 620 Series

Бренд: Agilent Technologies Страницы: 26

Бренд: Expo Börse Страницы: 53

Бренд: Homa Страницы: 72

Бренд: SANHOYA Страницы: 20

Бренд: Anest Iwata Страницы: 4

Бренд: samhydraulik Страницы: 9

Бренд: Trigano PISCINES Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды