Watts PVi CEN 1600 Скачать руководство пользователя страница 60

Страница: 60 / 124

OMM-0153_E

• 5/11/2023 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 60 of 124

CENTURION Installation, Operation & Maintenance Manual

SECTION 6: SAFETY DEVICE TESTING

Figure 6-8: Blower Proof Switch

Set the Controller’s

Enable/Disable

switch to

Enable

and wait for the Water Heater to

go into the Purge sequence.

5. After about 5 seconds, with air flowing into the combustion chamber, slowly turn the dial

clock-wise (to higher value) until the unit trips off with an

Air Flow Fault During Purge

message. Optionally, attach a manometer and measure the setting at the trip point.

6. After the Water Heater shuts down, reset the dial indicator to its original position, shown

on the switch cover label, then replace the switch cover.

7. Reset the Water Heater.

6.8.2 Blocked Inlet Switch Test

This test will be run in simulated fire mode, with the Blocked Inlet switch isolated from the rest of
the control circuitry.

Set the Controller’s

Enable/Disable

switch to

Disable

2. Remove the air filter (see Figure 6-7, above).

WARNING:

THE BLOWER SUCTION IS VERY STRONG AND CAN PULL NEARBY

OBJECTS INTO THE FAN BLADES!

3. Turn off the gas supply ball valve to the unit and then complete the following steps:

a) Use jumper wires to jump out the Low Gas Pressure switch and Blower Proof switch.

b) Remove the black connector boot from the Flame Detector.

Create a connector as shown below and connect it to the Flame Detector’s black
connector boot. Keep the alligator clip away from bare metal parts until step 5b.

Figure 6-9: Connecting the Flame Signal Generator

4. Go to

Diagnostics

→

Manual Run

and enable the

Manual Mode

control.

Ramp the Water Heater up to 100% fire rate and then set the Controller’s

Enable/Disable

switch to

Enable

Содержание PVi CEN 1600





























































































































Результаты поиска

Содержание PVi CEN 1600

Отзывы:

Похожие инструкции для PVi CEN 1600

Бренды по названию

Популярные бренды

Watts PVi CEN 1600, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание PVi CEN 1600

Отзывы:

Похожие инструкции для PVi CEN 1600

Бренды по названию

Популярные бренды