Wascomat EXSM 230 S Скачать руководство пользователя страница 81

Страница: 81 / 124

Trouble shooting

17E

Door status switch open,
even though the door lock is
locked.

Turn the machine’s wall switch off and on again.
Start a program.

Error code returns

No error code

Set program control unit to service mode. The
door status switch and door lock switch will now
be indicated by the LEDs shown left. Follow this
procedure (the door can be locked using code
23 and one press of the START button):

Door

Status of LEDs should be

for door lock switch: for door status
switch

open

OFF

closed, not locked OFF

closed and locked ON

Door lock switch LED ONDoor status switch LED
when door not locked OFF when door closed

Unscrew the door lock. Remove connection to
door lock switch "C" on door lock as illustrated.

LED ON

LED goes out

Remove PCB connector X71 from program
control unit PCB.

LED ON

LED goes out

Error codes which may arise on the control panel display

X71

Error code/symptoms

Fault-finding

2316

3390

Transient fault. No action
required.

Follow the chart for error code
02E to identify fault.

Cause/Action

Door lock faulty. Replace
lock.

Fault in wiring between PCB
and door lock. Check wiring
and replace if necessary.

Fault in program control unit
PCB. Replace PCB.

LEDs
indicating:

Door lock
switch

Door
status
switch

Содержание EXSM 230 S





























































































































Результаты поиска

Содержание EXSM 230 S

Отзывы:

Похожие инструкции для EXSM 230 S

Бренды по названию

Популярные бренды

Wascomat EXSM 230 S, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание EXSM 230 S

Отзывы:

Похожие инструкции для EXSM 230 S

Бренды по названию

Популярные бренды