Wascomat EXSM 230 S Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 124

background image

62

Electronic program control unit

Description

The program control unit is electronic and consists of a circuit board with
components. On one half are the microprocessor, program memory
(EPROM), power supply circuits, temperature and level control devices and
so on. On the other half are the relays and interference suppression
components. The program control unit has the following inputs and outputs:

•

Inputs reacting to push-buttons on the control panel.

•

Inputs which provide information on the machine’s door lock status, level
control, temperature sensors and coin mechanism if installed.

•

Outputs which via relays directly control the various functions of the
machine, e.g. motor control, water valves and door lock.

•

Outputs to the display.

•

Serial communication with the motor control unit.

The program control unit is controlled by the microprocessor, which fetches
its instructions from the program memory (EPROM). The EPROM contains
instructions for operation, the service program, control of relays, sensing of
inputs etc. The EPROM also contains the standard programs supplied with
the machine.

Fig.

76

X74
Temperature
sensor

X75
Motor control
unit

X76
Price=zero

X80
Valves

X81
Valves

X82
Valves

X83
Heating

X84
CP80

X71
Door lock

X72
Voltage feed

F1 (1A/250V)
For electronics

Buzzer

Microprocessor

Relays

Program memory (EPROM)

Level sensing
device

Service switch

2316

X79
Drain

X78
Input voltage

Interference
suppression
components

To
control
panel

X77
Coin mechanism

F2, F3 (1A/250V)
For display

76

Mechanical and electrical design

«
...
60
61
62
63
64
...
»

Содержание EXSM 230 S





























































































































Отзывы:

Нет отзывов

Похожие инструкции для EXSM 230 S

Бренд: Atag Страницы: 184

Бренд: Newworld Страницы: 44

Бренд: Asko Страницы: 24

Бренд: Unimac Страницы: 4

Бренд: GE Страницы: 40

Бренд: GreenWorks Страницы: 2

Бренд: LAVOR Pro Страницы: 96

Бренд: Smeg Страницы: 35

BI WDIL 75125 UK N

Бренд: Indesit Страницы: 4

Бренд: Tesla Страницы: 242

Бренд: Washtech Страницы: 12

Бренд: ZANKER Страницы: 48

Бренд: Hotpoint Страницы: 16

Бренд: Dacor Страницы: 42

Бренд: Kuppersberg Страницы: 148

Challeng Air AIRMAX

Бренд: Double K Industries Страницы: 4

Бренд: AYA Страницы: 48

Бренд: Landa Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды