WarmFlow Agentis Series Скачать руководство пользователя | Manualshive

Страница: 77 / 136

background image

Page

76

4.  The  burner  must  be  set  according  to  the  appliance  application  and
commissioned  checking  that  all  combustion  parameters  are  as  recommended  in
the appliance technical manual.
5. Warmflow recommends that the in line and burner oil pump filters are inspected
and  if  required  replaced  frequently  during burner  use,  before  the  burner start up
following a long period of discontinued operation and even more frequently where
contamination  has  occurred.  Particular  attention  is  needed  when  inspecting  and
checking for fuel leakages from seals, gaskets and hoses.

INSTALLER/SERVICER NOTES

1. During the burner installation, check that the gasoil and bio fuel blends are in
accordance with Riello recommendations (please refer to the chapters “Technical
Data”  and  “Guidance  for  the  use  of  bio  fuel  blends  within  the  burner  technical
manual).
2. If a Bio blend is in use the installer must seek information from the end user that
their fuel supplier can evidence that the blends of fuel conform to the relevant EN
standards.
3.  Check  that  the  materials  used  within  the  oil  tank  and  ancillary  equipment  are
suitable for bio fuels. If in doubt contact the relevant supplier or manufacturer.
4.  Particular  attention  should  be  given  to  the  oil  storage  tank  and  supply  to  the
burner.  Warmflow  recommends  that  existing  oil  storage  tanks  are  cleaned  and
inspected  and  any  traces  of  water  are  removed  BEFORE  bio  fuel  is  introduced
(Contact  the  tank  manufacturer  or  oil  supplier  for  further  advice).  If  these
recommendations  are  not  respected  this  will  increase  the  risk  of  contamination
and possible equipment failure.
5. Warmflow recommends a good quality bio compatible oil filter at the tank and a
secondary  filter  are  used  to  protect  the  burner  pump  and  nozzle  from
contamination. The filter sizes must be in line with the technical manual supplied
with the burners.
6. The burner hydraulic components and flexible oil lines must be suitable for bio
fuel use (check with Riello if in doubt).
7.  Regularly  check  visually  for  any  signs  of  oil  leakage  from  seals,  gaskets  and
hoses.
8. It is strongly recommended that with Bio fuel use, oil filters are inspected and
replaced every 4 months and more regularly where contamination is experienced.
9. During extended periods of non-operation and/or where burners are using oil as
a standby fuel, it is strongly recommended that the burner is put into operation for
short periods at least every three months.

Perfector 6 Side:Front

«
...
75
76
77
78
79
...
»

Содержание Agentis Series









































































































































Отзывы:

Нет отзывов

Похожие инструкции для Agentis Series

Бренд: DAXOM Страницы: 45

Бренд: Bakers Pride Страницы: 18

Бренд: U.S. Boiler Company Страницы: 180

Бренд: Riello Страницы: 28

Бренд: Green Mountain Страницы: 64

Compact 3020 HE

Бренд: Alde Страницы: 4

Бренд: Patterson-Kelley Страницы: 101

VOGUE MAX COMBI 40IE

Бренд: Ideal Heating Страницы: 24

Thermotank UKDAX-160GB25

Бренд: DAXOM Страницы: 29

Бренд: KYOWA Страницы: 3

Бренд: Biodom Страницы: 61

InterSystem HE26

Бренд: Atmos Страницы: 56

Format Slim HE 25 T

Бренд: Hermann Страницы: 36

Бренд: Alternate Heating Страницы: 66

Бренд: Absolute Страницы: 74

Vitoflex 300-RF Series

Бренд: Viessmann Страницы: 28

Бренд: Certikin Страницы: 29

Бренд: Ferroli Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды