Alternate Heating COAL GUN S130 Скачать руководство пользователя | Manualshive

Страница: 1 / 66

background image

INSTALLATION AND

OPERATOR’S MANUAL

COAL GUN™ BOILER

Models: S130 • S260

IMPORTANT

: IN ORDER TO ACHIEVE SAFE AND SATISFACTORY

RESULTS FROM YOUR ALTERNATE HEATING SYSTEMS BOILER, READ
SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE
INSTALLING AND OPERATING. ALL INSTALLATIONS MUST BE IN
ACCORDANCE WITH STATE AND LOCAL CODES. SAVE THESE
INSTRUCTIONS FOR FUTURE REFERENCE.

Your Alternate Heating Systems Boiler is capable of generating
very hot temperatures. Boiler temperatures and flames in the
ignition box area are capable of causing ignition or explosion of
explosive or flammable products or explosion of the boiler itself if
maximum safe water temperature is exceeded. Maximum safe
water temperature is 210° Fahrenheit. Flammable or explosive
products must never be stored in the same room or in the vicinity
of a boiler, and the boiler water temperature must never be
allowed to exceed 210° Fahrenheit.

ALTERNATE HEATING SYSTEMS

2393 LITTLE EGYPT RD
HARRISONVILLE, PA 17228
717-987-0099
WWW.ALTERNATEHEATINGSYSTEMS.COM
EMAIL: [email protected]

Record Model and Serial Number Below:

Model:
Serial Number:
Date of Purchase:

REV 170126

1
2
3
...
»

Содержание COAL GUN S130



































































Отзывы:

Нет отзывов

Похожие инструкции для COAL GUN S130

Бренд: Navien Страницы: 77

Бренд: Camus Hydronics Страницы: 108

atmoMAG 4/1 Z Series

Бренд: Vaillant Страницы: 12

Бренд: Adveco Страницы: 108

Бренд: Navien Страницы: 102

Alpha 500E (LPG)

Бренд: Alpha Страницы: 4

Бренд: Ideal Boilers Страницы: 4

ECO COMPACT 200

Бренд: Pleion Страницы: 11

Бренд: BRÖTJE Страницы: 168

Бренд: Sime Страницы: 48

Бренд: Sime Страницы: 16

Format System 25 HE

Бренд: Sime Страницы: 32

FORMAT DGT HE 12

Бренд: Sime Страницы: 32

Бренд: Protherm Страницы: 19

ATLAS D 30 K 100

Бренд: Ferroli Страницы: 100

NUVOLA DUO-TEC GA 16

Бренд: Baxi Страницы: 112

Бренд: Baxi Страницы: 144

BRAVA One HE 25

Бренд: Sime Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды