WarmFlow Agentis Series Скачать руководство пользователя | Manualshive

Страница: 23 / 136

background image

Page

22

1.18 Weather Compensation Operation

The Weather Compensation operates on the central heating system when the Outdoor Sensor
has been connected by the installer.

Depending  on  the  outdoor  temperature,  the  CH  flow  temperature  is  automatically  reduced
below the user CH setpoint.

The amount of reduction depends on the Weather Compensation Coefficient (Parameter ‘u 00’).

A lower value of Parameter ‘u 00’ results in a greater reduction of the CH flow temperature at a
given outdoor temperature.
A higher value of Parameter ‘u 00’ results in a smaller reduction of the CH flow temperature at a
given outdoor temperature.
Parameter ‘u 00’ is adjustable from 0 to 30.

The  maximum  setting  value  of  30  means  that  weather  compensation  is  not  active  when  the
outdoor temperature is less than 5°C, however the CH setpoint will be reduced the higher the
outdoor temperature rises above 5°C.

A value of 20 means that weather compensation is not active when the outdoor temperature is
less  than  -6°C,  however  the  CH  setpoint  will  be  reduced  the  higher  the  outdoor  temperature
rises above -6°C.

Care  should  be  taken  if  using  a  value  below  20  as  these  values  produce  very  aggressive
reductions in the CH setpoint.

«
...
21
22
23
24
25
...
»

Содержание Agentis Series









































































































































Отзывы:

Нет отзывов

Похожие инструкции для Agentis Series

Бренд: U.S. Boiler Company Страницы: 180

PUREFIRE PFW-199

Бренд: PEERLESS Страницы: 81

Caldariello Condens 25 KIS

Бренд: Riello Страницы: 55

Бренд: U.S. Boiler Company Страницы: 160

Alpha 500E (LPG)

Бренд: Alpha Страницы: 4

Бренд: Bosch Страницы: 308

Бренд: Hamworthy Страницы: 48

Бренд: Clean Energy Страницы: 54

Бренд: ARCA Страницы: 26

Бренд: HTP Страницы: 97

Бренд: Tilia Страницы: 24

BRAVA SLIM 30 BFR

Бренд: Sime Страницы: 60

GALAXI SMART Series

Бренд: Termoakim Страницы: 19

Бренд: Termodinamik Страницы: 32

Бренд: Viessmann Страницы: 120

Бренд: Viessmann Страницы: 156

Бренд: Viessmann Страницы: 200

Бренд: Aerco Страницы: 206

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды