manualshive.com logo in svg

Wacker Neuson AR, Руководство оператора

Поделиться
Скачать
Wacker Neuson AR Скачать руководство пользователя страница 24

10 Use and operation

100_0102_op_0003.fm

24

10 Use and operation

10.1

Safety

10.2

Prior to starting the machine

10.2.1

Checks before startup

The following parts must be checked for damage before each start-up.

Machine and components

Fastening clamp

Screws and fastening equipment

Power and extension cable

Safety belt

10.2.2

Checking the mains

Check if mains or power distribution on the construction site have the correct operating voltage (see 
nameplate of the machine or chapter 

Technical data

).

Check if mains or power distribution on the constructions site are protected in accordance with 
current standards and regulations.

Check whether the mains power is protected with a fault current protective switch (30 mA).

Check the connection values of this machine.

10.3

Fitting the machine

10.3.1

Before fitting

Ensure that any loose packaging has been removed from the machine.

Inspect the machine and its components for damage. If there is visible damage, do not operate 
machine but contact a Wacker Neuson representative immediately.

Check that all parts belonging to the machine (according to the delivery) have been delivered.

Check that you have the current local regulations relating to noise and light emissions. These 
regulations must be present when using this machine.

DANGER

Improper handling can lead to serious injuries or substantial material damage.

Read and follow all safety information of this manual - see chapter "Safety".

DANGER

Danger of electrocution. Damage on a component part of the machine or power cable can 
lead to serious injuries or death from the electric current.

Do not operate a damaged machine.

Have a damaged machine repaired immediately.

DANGER

Do not lay supply line in areas of traffic ways.

Damage of the Bodyguard® can lead to short circuit through entering water.

WARNING

Machine at risk of falling during operation.
Falling machine can cause serious injuries.

Ensure that no persons are in the danger zone.

Regularly check that machine is securely supported. Regularly check safety belt and 
fastening clamps.

NOTE

When fitting this machine to a formwork, all instructions and hazard warnings in this 
manual must be complied with. The "Assembly instructions – fastening clamp" must also 
be observed and the instructions and hazard warnings complied with.

Содержание AR































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды