manualshive.com logo in svg

Volvo D11 series, Руководство по установке


Поделиться
Скачать
background image

Marine engine environment

3

Other factors affecting performance

It is important to keep the exhaust backpressure at a 
low level. The power losses caused by backpressure 
are directly proportional to the increase of backpres-
sure, which also increases the exhaust temperature. 
Thermal values differ between markets and influence 
engine output. Environmental fuel, which is compul-
sory in some markets, has a low thermal value. En-
gine output may be reduced up to 8% compared with 
fuel specified in the ISO standard.

The weight of the boat is another important factor 
affecting boat speed. Increased boat weight has a 
major effect on boat speed, especially on planing and 
semi-planing hulls. A new boat tested with half filled 
fuel and water tanks and without a payload easily 
drops 2-3 knots in speed when tested fully loaded 
with fuel, water and equipment for travelling comfort. 
This situation arises because the propeller is often 
selected to give maximum speed when the boat is 
tested at the factory. It is therefore advisable to re-
duce propeller pitch by one or more inches when en-
countering hot climate and user load conditions. The 
top speed will be somewhat reduced but the overall 
conditions will improve and provide better accelera-
tion, even with a heavily loaded boat.

With this in mind it is important to remember that fi-
breglass boats absorb water when they rest in water, 
making the boat heavier over time. Marine growth, an 
often overlooked problem, also has a serious effect 
on boat performance.

Propeller selection

Naval architects, marine engineers or other qualified 
people should choose the propeller. The required en-
gine performance data to make the proper propeller 
selection is available in technical literature.

With regard to the propeller selection it is important 
to achieve correct engine RPM. For this purpose we 
recommend Full Throttle Operating Range.

In order to achieve good all-round performance the 
propeller should be selected within this range.

When the prototype and first production boat is built, 
a Volvo Penta representative and a boat manufactur-
er should undertake a fully loaded trial of the vessel 
as near as possible to the conditions that the boat will 
meet in the field. The most important conditions are:

•  Full fuel and water on board
•  Ballast evenly distributed throughout the boat to 

represent the owners’s equipment including such 
things as outboards, inflatable dinghies etc.

•  Genset/air conditioning equipment and all domes-

tic appliances fitted.

•  Adequate number of people onboard.
Once the vessel is subjected to these conditions a 
full engine/propeller trial should be undertaken where 
all engine parameters are checked, i.e. engine rpm, 
fuel consumption, rel. load, ref. rpm (EDC) boost 
pressure, exhaust temperatures, engine space tem-
peratures etc.

When the correct propeller has been established 
based on the tests, the engine rpm should be within 
the " Full Throttle Operating Range" at full load.

However, it is advisable to reduce pitch some more 
to handle varying weather conditions and marine 
growth. For this reason boat manufacturers must fol-
low the actual situation of their differing markets.

Propeller (too big)
Propeller (OK)
Propeller (too small)

Rated

Governor 

cut out

00% of full 

output. 

Full throttle 

operating 

range

Engine output, kW

rpm

Содержание D11 series





















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для D11 series

M.T.H. RailKing RKS SD70ACE Operator'S Manual preview
RailKing RKS SD70ACE
Бренд: M.T.H. Страницы: 12
um CBF 125 Service Manual preview
CBF 125
Бренд: um Страницы: 115
ZAFFER STC SHORT User Manual preview
STC SHORT
Бренд: ZAFFER Страницы: 28
Texas PowerLine TG500B Instruction Manual preview
PowerLine TG500B
Бренд: Texas Страницы: 98
ZIEHL-ABEGG ZAtop SM180.24/B Assembly Instructions Manual preview
ZAtop SM180.24/B
Бренд: ZIEHL-ABEGG Страницы: 16
Coleman EX300D52010 Parts Manual preview
EX300D52010
Бренд: Coleman Страницы: 24
Honda iGXV700 Owner'S Manual preview
iGXV700
Бренд: Honda Страницы: 48
Honda GV200 Owner'S Manual preview
GV200
Бренд: Honda Страницы: 5
Honda GCV520 Owner'S Manual preview
GCV520
Бренд: Honda Страницы: 60
DLE DLE200 User Manual preview
DLE200
Бренд: DLE Страницы: 13
FAAC TM2 ERY Manual preview
TM2 ERY
Бренд: FAAC Страницы: 116
Faro 486750 Manual preview
486750
Бренд: Faro Страницы: 5
Factory Five Racing Hot Rod Coyote Installation Instructions Manual preview
Hot Rod Coyote
Бренд: Factory Five Racing Страницы: 119
Mitsubishi DV173 Instruction Manual preview
DV173
Бренд: Mitsubishi Страницы: 16
Mitsubishi F9Q1 Workshop Manual preview
F9Q1
Бренд: Mitsubishi Страницы: 42
Nanni N4.115 Operator'S Manual preview
N4.115
Бренд: Nanni Страницы: 66
Ultima Competition Series Owner'S Manual preview
Competition Series
Бренд: Ultima Страницы: 40
Newport Vessels L-62 User Manual preview
L-62
Бренд: Newport Vessels Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды