manualshive.com logo in svg

Factory Five Racing Hot Rod Coyote, Руководство по установке

"Factory Five Racing Hot Rod Coyote" предлагает руководство по монтажу и инструкции по эксплуатации. Скачайте бесплатно полную версию руководства с manualshive.com. Воспользуйтесь нашим подробным руководством для установки и обслуживания вашего автомобиля, чтобы получить максимальное удовольствие от его использования. Узнайте все о продукте с нашим руководством!

Поделиться
Скачать
background image

 

Factory Five Racing, Inc. 

DO NOT DUPLICATE CONFIDENTIAL INFORMATION AND PROTECTED UNDER U.S. COPYRIGHT LAWS 

 2012 FACTORY FIVE RACING, INC.

 

Company/instructions

 

Part Number: 33871 

 

Revision: D 

 

Effective Date: 6/4/12 

 

 By:  J. INGERSLEV 

Document Type (indicate): 
 

 

 

 Bill of Material      

 

 Drawing (may be attached)  

 Specification 

 

 

 

 Assembly Instructions    

 

 Operating Procedure 

 

 Other 

Hot Rod Coyote Engine 

Installation Instructions  

 

Parts needed ..............................................................................................................................................................................2

 

Ford Racing Parts ..................................................................................................................................................................2

 

Ford Motor Co. Parts .............................................................................................................................................................3

 

Summit Racing ......................................................................................................................................................................3

 

Fuel System .......................................................................................................................................................................3

 

Air Intake System ..............................................................................................................................................................3

 

Other vendors ........................................................................................................................................................................3

 

Autozone ...........................................................................................................................................................................3

 

Supplies.....................................................................................................................................................................................3

 

Information ...............................................................................................................................................................................4

 

Engine prep ...............................................................................................................................................................................4

 

Oil filter relocator ..................................................................................................................................................................4

 

Oil Pressure sender ................................................................................................................................................................9

 

Water Temp Sender .............................................................................................................................................................13

 

Engine Bolts ........................................................................................................................................................................17

 

Alternator Boss....................................................................................................................................................................18

 

Transmission Prep ...................................................................................................................................................................19

 

Содержание Hot Rod Coyote
























































































































Отзывы:

Нет отзывов

Похожие инструкции для Hot Rod Coyote

Saito FG-84R3 Operating Instructions Manual preview
FG-84R3
Бренд: Saito Страницы: 8
CIMCO OXE Series Manual preview
OXE Series
Бренд: CIMCO Страницы: 24
jiangdong JF120 Owner'S Manual preview
JF120
Бренд: jiangdong Страницы: 27
Deutz TBD 616 OEM Operating Instructions Manual preview
TBD 616 OEM
Бренд: Deutz Страницы: 257
Navistar MaxxForce 3.2H Euro V Operation And Maintenance Manual preview
MaxxForce 3.2H Euro V
Бренд: Navistar Страницы: 116
JVL MAC050 User Manual preview
MAC050
Бренд: JVL Страницы: 306
JVL MIS23 Series User Manual preview
MIS23 Series
Бренд: JVL Страницы: 347
Omron SGDH-01AE-OY Datasheet preview
SGDH-01AE-OY
Бренд: Omron Страницы: 18
Omron OMNUC G User Manual preview
OMNUC G
Бренд: Omron Страницы: 438
Optec QuickSync FT20 Installation Manual preview
QuickSync FT20
Бренд: Optec Страницы: 10
Beta Enduro RR 350 2015 Workshop Manual preview
Enduro RR 350 2015
Бренд: Beta Страницы: 158
Texas Equipment TG370 User Manual preview
TG370
Бренд: Texas Equipment Страницы: 25
Volvo D13F Operator'S Manual preview
D13F
Бренд: Volvo Страницы: 20
Volvo D13 User Manual preview
D13
Бренд: Volvo Страницы: 51
Volvo D13H Driver'S Handbook Manual preview
D13H
Бренд: Volvo Страницы: 76
YS 91SR Operator'S Manual preview
91SR
Бренд: YS Страницы: 2
ARO 50 SERIES Operator'S Manual preview
50 SERIES
Бренд: ARO Страницы: 8
O.S. engine max-18tz series Owner'S Instruction Manual preview
max-18tz series
Бренд: O.S. engine Страницы: 25

Бренды по названию

Популярные бренды

Загрузить еще бренды