Volvo Penta DPS-A Скачать руководство пользователя

Страница: 28 / 208

Sterndrive, General Information

Publ. 7746477

English

06-2008

Coat propeller shaft and inside of prop hub with grease

828250

Future removal of the propeller will be difficult if this is not done.

NOTICE!

Failure to install all components could result in

propeller loss and damage to sterndrive.

Place thrust bushing (B) on propeller shaft with inner taper toward
gearcase.

Install propeller on shaft, aligning splines, and push propeller onto
the thrust bushing until the splines are exposed.

Install thrust washer (D) on propeller shaft splines.

Install propeller nut (E).
Torque to

70-80 ft. lb. (95-108 N•m)

Index keeper (F) on propeller nut until a slot is aligned with cotter
pin hole.

Install the cotter pin and bend the ends to secure; use a new cotter
pin if necessary.

Shift the sterndrive into

neutral

to check propeller movement.

Propeller should turn freely.

6604B

6602

6598

Содержание DPS-A

















































































































































































































Результаты поиска

Содержание DPS-A

Отзывы:

Похожие инструкции для DPS-A

Бренды по названию

Популярные бренды

Volvo Penta DPS-A, Руководство по ремонту

Результаты поиска

Содержание DPS-A

Отзывы:

Похожие инструкции для DPS-A

Бренды по названию

Популярные бренды