Volvo Penta DPS-A Скачать руководство пользователя

Страница: 109 / 208

SX-A Lower Gearcase

Publ. 7746477 English 06-2008

105

Apply a light coat of gear oil to inner diamter of large bearing.

Slide bearing on shaft with taper facing away from small bearing.

Place bearing installer

3850617

on open jaws of a press support.

Position raised lip of installer up; it must contact nose of
bearing.

Insert shaft into installer, and press shaft in bearing until it seats.

Pinion Shimming

NOTICE!

This procedure determines the amount of shims

required to properly position the pinion in relation to

the propshaft gear. Record the following shimming

measurement for the final gear lash check.

Measure for Shims

Clamp special tool

884830

(S) in a vice and place vertical shaft in

socket. Place cup (C) on small bearing.

Slide shim fixture 3855098 (F) on shaft with three slots facing
threaded end of shaft.

Install pinion and pinion nut.

Torque nut to 150-160 ft. lb. (203-217 N

•

m).

Rotate shim fixture to seat bearing for shimming purposes.

50563

Содержание DPS-A

















































































































































































































Результаты поиска

Содержание DPS-A

Отзывы:

Похожие инструкции для DPS-A

Бренды по названию

Популярные бренды

Volvo Penta DPS-A, Руководство по ремонту

Результаты поиска

Содержание DPS-A

Отзывы:

Похожие инструкции для DPS-A

Бренды по названию

Популярные бренды