Volvo Penta DPS-A Скачать руководство пользователя

Страница: 189 / 208

Transom Shield Assembly

Publ. 7746477 English 06-2008

185

Hydraulic Lines Removal

NOTICE!

The trim system is a hydraulic system and is extremely

sensitive to dirt and debris. Only remove the hydraulic

lines and/or trim pump if you have a problem with the

trim system.

Remove two screws that secure the hydraulic line retainer to the
trim pump.

Remove the hydraulic lines from the trim pump

Trim Pump Removal

Mark the connector for the positive (+) and negative (-) wires.

Using a pair of needle nosed pliers, remove the red plastic insert
in the connector.

Using a probe, lift the locking tab (A) for the connector terminals
and remove the terminals through the rear of the connector.

Disconnect hydraulic lines from trim pump. See “Hydraulic Lines
Removal” on page 185.

Remove the six retaining screws on the trim pump housing.

Remove pump from transom shield.

Pull the power feed wires through the transom shield.

NOTICE!

Use caution when pulling the trim pump wires through

the transom shield. The wires connected to the electric

motor may pull loose. Push the wires through the

transom shield while removing the trim pump.

Содержание DPS-A

















































































































































































































Результаты поиска

Содержание DPS-A

Отзывы:

Похожие инструкции для DPS-A

Бренды по названию

Популярные бренды

Volvo Penta DPS-A, Руководство по ремонту

Результаты поиска

Содержание DPS-A

Отзывы:

Похожие инструкции для DPS-A

Бренды по названию

Популярные бренды