Volvo Penta DPS-A Скачать руководство пользователя

Страница: 31 / 208

Sterndrive, General Information

Publ. 7746477 English 06-2008

Install the rear propeller nut, chamfered edge forward.

NOTICE!

Be sure the chamfered edge of the propeller nut is

facing forward. Failure to install the propeller nut

correctly could result in a propeller coming loose and

damge to the lower unit and/or propeller.

Torque nut to 50 ft. lb. (70 N•m).
Use prop nut tool

3862808

or 30 mm socket and torque wrench.

NOTICE!

Failure to install the propellers as indicated could

result in a propeller coming loose and damge to the

lower unit and/or propeller.

Remove dipstick and oil level plug (under shift cover) so sterndrive will
vent and drain completely

Shift the drive in to

neutral

Both propellers should turn freely.

Anodes

The drive anode is located on the top of the caviatation plate.

Replacing

Anode erosion or disintegration in salt or brackish water indicates the
anode is functioning correctly. Anodes should be inspected and/or
replaced at regular intervals, or corrosion of the drive will increase.

NOTICE!

Replace anode when it is reduced to two-thirds of

original size (one-third eroded).

Replacement anode kits contain new mounting screws. The new
screws have pre-applied Locktite ™ and should always be used when
installing new anodes.

Torque anode screws to 15-20 ft. lb. (20-28 N•m)

Materials

Anodes are offered in three materials (metals);

Aluminum

- for use when the boat (drive) will be used in multiple

water types; fresh, salt or brackish. Also best when the water type
where the boat will be operated is not known.

Zinc

- for use in salt water

Magnesium

- for use in fresh water

50612

Содержание DPS-A

















































































































































































































Результаты поиска

Содержание DPS-A

Отзывы:

Похожие инструкции для DPS-A

Бренды по названию

Популярные бренды

Volvo Penta DPS-A, Руководство по ремонту

Результаты поиска

Содержание DPS-A

Отзывы:

Похожие инструкции для DPS-A

Бренды по названию

Популярные бренды