Volvo Penta DPS-A Скачать руководство пользователя | Manualshive

Страница: 9 / 208

background image

General Information

Publ. 7746477 English 06-2008

5

penetrative energy, so the fuel can penetrate deep into the body tissue
and cause serious personal injury.

Never expose a battery to open flame or sparks. Never smoke in

the proximity of batteries. The batteries give off hydrogen gas during
charging which, when mixed with air, can form an explosive gas -
oxyhydrogen. This gas is easily ignited and highly volatile. Incorrect
connection of the battery can cause an explosion with resulting
damage. Do not cross the connections when attempting to start the
engine (spark risk) and do not lean over any of the batteries.

Always use protective goggles when charging the batteries or making
battery connections. Battery electrolyte contains sulfuric acid, which is
highly corrosive. If the battery electrolyte comes into contact with
unprotected skin, wash immediately with plenty of water and soap. If
battery acid comes in contact with the eyes, immediately flush with
plenty of water and obtain medical assistance at once.

To prevent sparks which can ignite fumes, turn off the engine and turn
off all electrical power at the main switch, or disconnect the battery
negative (-) lead, before carrying out work on the electrical system.

Contact with AC current can be fatal. Take extra precautions when

working on boats with AC systems. Completely disconnect the system
when making any repairs where the work could come permit contact
with the AC system. Make sure the boat AC system is connected to a
proper and tested ground.

Use the lifting eyes fitted on the engine/reverse gear when lifting the
unit. Always check that the lifting equipment used is in good condition
and has the load capacity to lift the engine (engine weight including
reverse gear and any extra equipment installed).

Use an adjustable lifting beam or one designed specifically for the
engine to raise the engine to ensure safe handling and to avoid
damaging engine parts installed on the top of the engine. All chains
and cables should run parallel to each other and as perpendicular as
possible in relation to the top of the engine.

If extra equipment is installed on the engine, which alters its center of
gravity, a special lifting device is required to obtain the correct balance
for safe handling.

The components in the electrical system, in the ignition system
(gasoline engines), and in the fuel system on Volvo Penta products
are designed and manufactured to minimize the risk of fire and
explosion. Do not substitute automotive or other non-approved non-
marine parts for these components.

Carefully observe the safety alert symbols shown for dangers,
warnings, and cautions exactly as described. They warn you of
possible dangers or important information contained in this manual.

«
...
7
8
9
10
11
...
»

Содержание DPS-A

















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DPS-A

SACE Tmax XT Series

Бренд: ABB Страницы: 11

Бренд: Olympus Страницы: 86

Бренд: Baoding Longer Precision Pump Страницы: 6

Бренд: ParaBody Страницы: 3

Бренд: Hach Страницы: 52

Бренд: hager Страницы: 2

Бренд: ICP DAS USA Страницы: 45

ProFire Lightbridge

Бренд: M-Audio Страницы: 8

Бренд: M-Audio Страницы: 36

9NP-B7524 Series

Бренд: Nautilus Страницы: 2

Be strong NS 700X

Бренд: Nautilus Страницы: 34

Бренд: Nautilus Страницы: 21

Бренд: Raven Страницы: 48

Бренд: Pacific Страницы: 16

Бренд: V-TAC Страницы: 13

Saturn 2000 GC/MS

Бренд: Varian Страницы: 9

Бренд: Y.I.C. TECHNOLOGIES Страницы: 6

VIMCO Sivoia SV-CCI-GRP

Бренд: Lutron Electronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды