Volvo Penta DPS-A Скачать руководство пользователя

Страница: 118 / 208

SX-A Lower Gearcase

114

Publ. 7746477

English

06-2008

Measure (M) gap between bearing housing (B) and gearcase (L).

Record in two places, in the middle on each side.

Average the measurements.

NOTICE!

Do not measure at gap (G) at bottom and top of

housing.

Round off the average amount.

This is the shim amount for the propshaft bearing housing.

Example:

Remove bearing housing.

Install shims and re-install bearing housing.

10.

Install original screws and torque to 10 ft. lb.

(13,5 N’m)

Then tighten screws another 70° of rotation.

NOTICE!

Use original screws for all shimming, rolling torque

and other pre-assembly work. Use two NEW screws for

final assembly and final torque.

50610

Add:

Divide:

no. 1 = 0.014 in.

0.031 in. / 2= 0.0151 in.

no. 2 = 0.017 in.

round to 0.015 in.

Total 0.031 in.

50616

50622

Содержание DPS-A

















































































































































































































Результаты поиска

Содержание DPS-A

Отзывы:

Похожие инструкции для DPS-A

Бренды по названию

Популярные бренды

Volvo Penta DPS-A, Руководство по ремонту

Результаты поиска

Содержание DPS-A

Отзывы:

Похожие инструкции для DPS-A

Бренды по названию

Популярные бренды