Volvo Penta DPS-A Скачать руководство пользователя

Страница: 117 / 208

SX-A Lower Gearcase

Publ. 7746477 English 06-2008

113

Propshaft Bearing Housing,

Shimming and Rolling Torque

NOTICE!

This procedure determines the amount of shims

required to preload the propshaft bearings, and also

ensures bearing life by setting the vertical shaft and

propshaft rolling torque.

Install propshaft/bearing in gear.

Install bearing housing (no seal).

Do not install o-rings or shims.

Place bearing housing over shaft and in to bore in gearcase.

Install housing, use original screws removed during disassembly.

NOTICE!

Use the same type of screw that was removed if any

require replacement. If a socket head screw was

removed, a socket head screw must be used to replace

it. Flange type screws are not compatible with early

propshaft bearing housings.

Tighten screws in small steps, alternating top and bottom, until
vertical shaft rolling torque is;

• for ratios 1.43, 1.51, 1.60, 1.79, 1.89: 1

4-23 in.lb.

(

1,58-2,60

•

m).

• for ratios 1.66, 1.97, 2.18:

11-18 in. lb. (1,24-2,03 N

•

50607

50608

50609

Содержание DPS-A

















































































































































































































Результаты поиска

Содержание DPS-A

Отзывы:

Похожие инструкции для DPS-A

Бренды по названию

Популярные бренды

Volvo Penta DPS-A, Руководство по ремонту

Результаты поиска

Содержание DPS-A

Отзывы:

Похожие инструкции для DPS-A

Бренды по названию

Популярные бренды