manualshive.com logo in svg

Volvo Penta DPS-A, Руководство по ремонту


Поделиться
Скачать
background image

DPS-A Lower Gearcase

142

Publ. 7746477

English

06-2008

Passages for Pitot

If pitot (speedometer) is clogged, use compressed air to clear the 
passages. Apply air at opening to smaller passage on leading edge of 
gearcase.

Water Intakes

If needed, water intakes can be removed.
Remove two screws from port intake.

Gearcase Magnet

There is a magnet mounted in the front of the gearcase, forward of the 
propshaft gear. No service is needed and the magnet should not be 
removed during routine gearcase service.

If the magnet is removed, when reinstalling, torque screw to 5-7 ft. lb. 
(7-9 N•m) .

NOTICE!

Most threaded holes in gearcase have Heli-Coil

inserts. 

Do not use a thread tap to clean screw holes. Tap will 

damage Heli-Coil insert and make replacement 

necessary. Do not replace with standard non-locking 

Heli-Coils. 

•

Retainer Threads

- lock ring must turn freely for full depth.

•

Cooling Passages

- check for corrosion build-up that would 

restrict water circulation.

•

Propshaft Bearing Carrier Bore

- remove all sharp edges that 

would cut o-ring.

•

Gears, Shafts and Bearings

- inspect gear teeth for cracks 

and chips or discoloration. If any gear is damaged all must be 

50614

50578

50615

Содержание DPS-A

















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DPS-A

OfiTE PPT Instruction Manual preview
PPT
Бренд: OfiTE Страницы: 21
Earthlite Deluxe Quick Start Manual preview
Deluxe
Бренд: Earthlite Страницы: 4
YATEK Deluxe Mounting And User Manual preview
Deluxe
Бренд: YATEK Страницы: 78
EWM Tetrix 351 AC/DC Smart FW Operating Instructions Manual preview
Tetrix 351 AC/DC Smart FW
Бренд: EWM Страницы: 117
Raytech TR-1 Instruction Manual preview
TR-1
Бренд: Raytech Страницы: 21
Teac LX Series Specifications preview
LX Series
Бренд: Teac Страницы: 2
laerdal HEARTSTART Quick Start Manual preview
HEARTSTART
Бренд: laerdal Страницы: 2
ABS ABS-Lock DH04 Series Manual preview
ABS-Lock DH04 Series
Бренд: ABS Страницы: 4
BACtrack VIO User Manual preview
VIO
Бренд: BACtrack Страницы: 13
Badgematic FLEXI Manual preview
FLEXI
Бренд: Badgematic Страницы: 28
BACtrack Select S80 Product Specifications preview
Select S80
Бренд: BACtrack Страницы: 2
MADRIX STELLA Quick Start Manual & Technical Manual preview
STELLA
Бренд: MADRIX Страницы: 28
BACTcontrol microLAN Software Manual preview
microLAN
Бренд: BACTcontrol Страницы: 28
Tascam HS-20 Owner'S Manual preview
HS-20
Бренд: Tascam Страницы: 128
ParaBody 842 User Manual preview
842
Бренд: ParaBody Страницы: 6
GARANT SG1 Operation Manual preview
SG1
Бренд: GARANT Страницы: 239
p-light Midi Installation And Instructions For Use preview
Midi
Бренд: p-light Страницы: 36
Yamaha TG500 Supplementary Manual preview
TG500
Бренд: Yamaha Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды