Volvo Penta DPS-A Скачать руководство пользователя

Страница: 153 / 208

DPS-A Lower Gearcase

Publ. 7746477 English 06-2008

149

10.

The rear gear markings/etchings are on the outer propshaft.
Forward gear mark is in the box marked

11.

Add or subtract shimming allowance number etched on gear from
number found in Step 9.;

If the etched number is

, you would

ADD 0.005 in.

to actual

dimension in Step 9.

If the etched number is

-5

, you would

SUBTRACT 0.005 in.

from

actual dimension in Step 9.

If the etched number is -0-, use the actual dimension from Step 9.

Example:

Add/Subtract:

0.221 in. actual dimension in Step 9

0.002 in. etched number (+2) on gear

0.223 in. total shims required

12.

Record dimension (example: 0.223 in.) for the outer propeller shaft
shims required.

13.

Remove parts from shim fixture.

Bearing Race and Shim Installation

NOTICE!

Use the least number of shims possible to obtain the

required shim thickness.

Place needed thickness of shims in recess of bearing race bore.

NOTICE!

No less than one shim but no more then three shims

should be used.

Apply gear oil to the bearing race.

Place race on top of shims in gearcase.

Screw race installer

3849657

(N) on handle

3850609

Slide guide plate

3849656

(P) on handle.

(R)

(P)

(F)

50957

(F)

((R)

(P)

50574

50575

Содержание DPS-A

















































































































































































































Результаты поиска

Содержание DPS-A

Отзывы:

Похожие инструкции для DPS-A

Бренды по названию

Популярные бренды

Volvo Penta DPS-A, Руководство по ремонту

Результаты поиска

Содержание DPS-A

Отзывы:

Похожие инструкции для DPS-A

Бренды по названию

Популярные бренды