Victory BX42S Скачать руководство пользователя | Manualshive

Страница: 13 / 51

background image

Operator

’s Manual Victory BX42S

- Page 13 of 51 -

Version 2.0

◼

When lifting heavy parts, use a hoist or ask for help, to prevent personal injury.

◼

Ensure that all hoisting equipment such as lifting straps, hooks, or ropes are in a good state of
repair and that they can safely bear the equipment's weight.

◼

Never bypass door interlocks or safety sensors and switches.

◼

Leaking chemicals, oil, or water on electrical equipment can result in severe damage or fire.

◼

Watch for hot parts on switched-off components and hot liquids in lines, pipes, and
compartments to prevent burns.

◼

Never open any vent or drain valve or remove any plugs while the system is under pressure.

◼

Ensure that oil pumps are isolated from the system and relieve the pressure before
disassembling a pump, removing plugs, or disconnecting piping.

◼

Always use tools that are in a good state of repair. Ensure you know how to use the tools
before doing any work.

◼

ONLY use replacement parts from the same brand as the relevant part.

◼

Always use replacement fittings having the same part number (or equivalent). Do not use
fitting of inferior quality.

◼

Do not make any repairs if you are tired or consume alcohol or drugs, affecting your ability to
work perfectly.

◼

PROTECT THE ENVIRONMENT: The handling and cleaning of spent oil or chemicals may be
subject to national or local laws and regulations. Use authorized waste processing services,
including Municipal facilities and garages, which provide official facilities for collecting oil and
chemicals.

◼

Contact the provincial or Municipal authorities or the Environmental Protection Service for
guidelines about handling correctly and cleaning up spent oil and chemicals if in doubt.

◼

Parts that rotate can cause cuts, mutilations or strangulation.

◼

Always switch OFF the main power before performing service and maintenance.

◼

Do not allow water or any other fluid to contact electrical components.

◼

Switch the power ON only after closing all machine protection guards and covers.

◼

Never use a high-pressure water beam for cleaning electrical components and cabinets.

◼

Do not aim a high-pressure water beam directly at wiring, breathers, or hydraulic components'
sealings of drive components.

◼

Always protect venting spots from the inlet of large amounts of water.

«
...
11
12
13
14
15
...
»

Содержание BX42S




















































Отзывы:

Нет отзывов

Похожие инструкции для BX42S

Бренд: YAAHKIEH Страницы: 16

Бренд: Jensen Страницы: 72

Бренд: Daikin Страницы: 88

Бренд: Wallenstein Страницы: 76

Бренд: McQuay Страницы: 68

Бренд: Sinbo Страницы: 44

AP20BCF200-3-XL

Бренд: American Panel Страницы: 36

2E9US1110PS051112

Бренд: Wallenstein Страницы: 68

Бренд: SMC Networks Страницы: 29

Бренд: LG Страницы: 77

Vacuum & Trim Titanium HKVAC-2000

Бренд: Remington Страницы: 7

Shortcut clipper SCC-100R

Бренд: Remington Страницы: 36

Бренд: Remington Страницы: 76

Бренд: Remington Страницы: 164

Бренд: Polar Refrigeration Страницы: 44

Бренд: Polar Refrigeration Страницы: 48

Бренд: Elkay Страницы: 2

Бренд: Elkay Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды