Victory BX42S Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 51

background image

Operator

’s Manual Victory BX42S

- Page 17 of 51 -

Version 2.0

Some common areas of interference are:

◼

Three-point linkage.

◼

Extended or eye loop hitch pins.

3.10

Guarding

To not effectively eliminated hazards, provide guarding whenever feasible.

The PTO master, critical driveline, and input connection shield should offer an interactive guarding
system.

◼

Provide instructions by labels or manuals. Use the implement only with the

tractor’s PTO

master shield.

◼

Specify and test an integral driveline shield with end cones that overlap but do not interfere
with the PTO master shield or implement an input connection shield.

◼

Provide an input connection shield to interact with the integral driveline shield to guard the
shaft coupling and any torque limiting devices installed on the driveline.

◼

Check that all routine driveline maintenance can be done without removing the shields.

3.11

Warnings and Instructions

Provide warnings and instructions for hazards associated with the device. Provide instructions for
proper maintenance and repair.

◼

Provide labels on the unit to advise the user of proper hitch dimensions and maximum safe
operating speed.

◼

Check that proper danger labels are supplied with the driveline concerning these parameters

may be found in all driveline manufacturer’s

catalogs.

◼

The operator's manual provides instructions for proper driveline operation, maintenance, and
repair.

◼

Advise against using PTO adapters,

which may defeat the purpose of the tractor’s master

shield

and adversely affect the driveline's performance.

◼

Advise the user of locations of genuine original equipment spare parts.

3.12

ASME standards

You can obtain further information about driveline specifications and safety from your driveline
supplier and the following ASME standards and engineering practices:

◼

S203

Rear power take-off for agricultural tractors.

◼

S205

Power take-off definitions and terminology of farming tractors.

◼

S207

Operating requirements for tractors and power take-off driven equipment implements.

◼

S318

Safety for agricultural equipment.

◼

S331

Implement power take-off driveline specifications.

◼

S333

Agricultural tractor auxiliary power take-off drives.

◼

S350

Safety alert symbol for agricultural equipment.

◼

S441

Safety signs.

◼

S493

Guarding for agricultural equipment.

◼

EP363

Technical publications for agricultural equipment.

«
...
15
16
17
18
19
...
»

Содержание BX42S




















































Отзывы:

Нет отзывов

Похожие инструкции для BX42S

YCIV 0590-1500 50Hz

Бренд: York Страницы: 12

Бренд: Sencor Страницы: 7

Бренд: Cornelius Страницы: 52

Бренд: Skope Страницы: 12

Бренд: Beurer Страницы: 104

Бренд: Vermeer Страницы: 100

Бренд: Cub Cadet Страницы: 20

Бренд: Yardbeast Страницы: 25

Бренд: ClimaCool Страницы: 92

Бренд: VALERA Страницы: 94

Бренд: BaByliss PRO Страницы: 64

COOL CABI OCA-S300BC

Бренд: OHM ELECTRIC Страницы: 48

Бренд: Daikin Страницы: 24

Бренд: Coolzone Страницы: 8

Бренд: ECG Страницы: 64

Бренд: Advantage Страницы: 64

Бренд: Thermo Страницы: 27

Бренд: Timberwolf Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды