Victory BX42S Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 51

background image

Operator’s Manual Victory BX42S

- Page 26 of 51 -

Version 2.0

4.1.2

Install the PTO shaft

◼

Fit the PTO shaft between the tractor and implement. Watch the position of the shear bolt.

◼

Raise and lower the implement to find the maximum extended PTO shaft length. Check to
ensure that the PTO s

haft’s overall length does not exceed the

full recorded size.

◼

If needed, set the tractor’s 3

-Point lift height to keep the PTO shaft from exceeding the

maximum allowable length.

NOTE:

Attacht the one end with the

shear bolt to the woodchipper.

◼

Secure the chain to the tractor and
implement. This will prevent the
shield from spinning during
operation.

4.1.3

Checking the PTO Shaft’s Interference

Maximum PTO Shaft movement.

◼

Slowly engage the tractor’s hydraulic 3

-Point hitch to lower the implement while checking for

sufficient drawbar clearance. Move the drawbar ahead, aside, or remove it if required.

◼

Set the tractor’s 3

-Point hitch lift height to keep the PTO shaft from exceeding the maximum

allowable length and 25° up or down.

«
...
24
25
26
27
28
...
»

Содержание BX42S




















































Отзывы:

Нет отзывов

Похожие инструкции для BX42S

Magnitude WMC Series

Бренд: Daikin Страницы: 68

Бренд: LG Страницы: 77

PRO POWER HC5150

Бренд: Remington Страницы: 125

Бренд: Clint Страницы: 36

Бренд: Victory Страницы: 64

Premium CR 2821

Бренд: camry Страницы: 56

Бренд: Moser Страницы: 148

45 COMBISET BLAST CHILLER

Бренд: Fulgor Milano Страницы: 192

Бренд: decakila Страницы: 19

Бренд: Vitek Страницы: 40

Бренд: WaterFurnace Страницы: 68

Бренд: Randell Страницы: 17

Бренд: Panasonic Страницы: 16

Бренд: Patriot Страницы: 4

Бренд: lancer Страницы: 15

Бренд: Qettle Страницы: 4

Бренд: Jensen Страницы: 59

Бренд: TECHWOOD Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды