Velodyne VLP-16 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 138

Velodyne VLP-16 Скачать руководство пользователя страница 50

8.2.2 Position Packet Rate

Position packets arrive at approximately 1/14th the rate of data packets.

554 bytes/packet * 753.5 packets/second / 14 = 29817 bytes/second

8.2.3 Total Packet Rate

Summing yields 970185 bytes/second for single return mode.

Dual return mode doubles the data rate but not the position packet rate: (2 * 970185 bytes/second) + 29817 bytes/second
= 1970187 bytes/second

8.2.4 Laser Measurements Per Second

A laser firing results in a single data point, which is a measurement of distance to target and its reflectivity.

16 laser firings/data block * 24 data blocks/packet = 384 laser firings/packet

8.2.4.1 Single Return Mode (Strongest, Last)

384 laser firings/packet * 753.5 packets/second = 289344 laser measurements per second

8.2.4.2 Dual Return Mode

384 laser firings/packet * 1507 packets/second = 578688 laser measurements per second

8.3 Rotation Speed (RPM)

The sensor’s motor can be set to rotate between 300 RPM and 1200 RPM, inclusive, in increments of 60 RPM (e.g. 300,
360, 420, 480, … 1140, 1200).

Note: If the RPM setting is not evenly divisible by 60, neither motor speed control nor phase lock functions will
function properly.

The user can set this parameter using the sensor’s Web Interface or curl commands. See

Configuration Screen on

or

Sensor Control with curl on page 76

for more on setting rotation speed.

Note: In VeloView, one rotation can be referred to as a single “frame” of data, beginning and ending at approximately 0°
azimuth. The number of frames per second of data generated depends entirely on the RPM setting, e.g. 600 RPM / 60
s/min = 10 frames per second.

Choice of RPM is up to the user and depends on the application. For example, an autonomous vehicle may wish to
increase rotation speed so it could more quickly identify frame-to-frame variations in the environment, such as a child run-
ning across a street. Conversely, a cart-based mapping solution might use a lower RPM to increase the detail in each
frame.

8.3.1 Horizontal Angular (Azimuth) Resolution

Because the firing timing of the sensor is fixed at 55.296 μs per firing cycle, the speed of rotation changes the angular res-
olution of the sensor.

An example calculation for 600 RPM is given in

Equation 8-1 below

.

Equation 8-1 Azimuth Resolution at 600 RPM

50

VLP-16 User Manual

«
...
48
49
50
51
52
...
»

Содержание VLP-16











































































































































Отзывы:

Нет отзывов