manualshive.com logo in svg

Valco baby Vici TCD-3, Инструкция по эксплуатации

Поделиться
Скачать
Valco baby Vici TCD-3 Скачать руководство пользователя страница 4

Table of Contents  

(continued)

TCD Operation with the Graphical User Interface ........................................................................21 

Control Screen ..................................................................................................................................21 
Configuration Screen .....................................................................................................................22 
Graph Screen ....................................................................................................................................26 

STATUS LED States and Troubleshooting ........................................................................................28

Maintenance ..............................................................................................................................................29 

Cleaning the Enclosure .................................................................................................................29 
Bake Out Procedure ........................................................................................................................29

Appendix A:  Digital I/O Control ..........................................................................................................30 

Digital I/O Port ..................................................................................................................................30 
Digital I/O Connector .....................................................................................................................30 
Digital Signal Inputs .......................................................................................................................31 
Digital Input Functions ..................................................................................................................31 
Digital Output Signal .....................................................................................................................31

Appendix B:  Basic Control of the TCD via Serial Commands ...................................................32 

Establishing Serial Communication ..........................................................................................32 
Initial Bakeout and Equilibration ...............................................................................................33 

Initial Conditioning ..............................................................................................................33 
Temperature Settings..........................................................................................................33 

Balancing the Channels ................................................................................................................33 
Serial Communication Protocols ...............................................................................................34 

General Console Port Usage .............................................................................................34 
Interface Command Editing .............................................................................................34 

Serial Commands ............................................................................................................................35

Appendix C:  Heater and Filament Connector Signal Descriptions and 

Connection Matrices ......................................................................................................................36

Warranty  .....................................................................................................................................................37

Detector Performance Log ...................................................................................................................38

Содержание Vici TCD-3











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды