manualshive.com logo in svg

Valco baby Vici TCD-3, Инструкция по эксплуатации

Поделиться
Скачать
Valco baby Vici TCD-3 Скачать руководство пользователя страница 20

16

Figure 8:

  TCD-3 cable connections

Installation

Flow Rate Settings

Since the TCD-3 is a concentration-dependent detector, the lower the flow rate 
through the detector, the higher the sensitivity.  Column diameter will determine 
the optimum column flow rate.
The microvolume TCD-3 is designed for the lower flow rates typical for capillary 
columns, and achieves best sensitivity at rates below 10 mL/min.  Since the fila-
ments are maintained at constant temperature, the detector can be operated at 
extremely low flow rates (less than 0.5 mL/min) without damage to the filaments.
1.  Measure the column flow at the detector’s Channel A out.  The optimum flow 

rate is in the range of 4 – 20 mL/min, with the actual rate dependent on the 
type of column used.

2.  Measure the reference gas flow at Channel B out.  It should be as close as  

possible to the GC column flow.  Use a fixed flow restrictor or a good quality 
flow controller to match the carrier gas and reference gas flows.

3.  Once the flows have been established, connect the 48VDC power supply to the 

TCD controller unit, plug it into an appropriate source, and turn the power on 
via the rear panel switch.

 

Содержание Vici TCD-3











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды