manualshive.com logo in svg

Valco baby Vici TCD-3, Инструкция по эксплуатации

Поделиться
Скачать
Valco baby Vici TCD-3 Скачать руководство пользователя страница 17

13

Installing and Purging a Purifier

1.  If the pressure regulator has a 1/8" male cone-type outlet port, install a Valco 

1/8" external to 1/16" internal reducer (EZR21); if it has a 1/4" male cone-type 
outlet port, install a Valco 1/4" external to 1/16" internal reducer (EZR41).  For 
other regulator outlet fittings, a wide variety of Valco adapters are available.

2.  While keeping the outlet tube capped, remove the cap from the inlet tube 

of the Valco helium purifier and insert the tube fitting into the 1/16" reducer 
port.  Use a 1/4" wrench to turn the nut one-quarter turn past the point where 
the ferrule first starts to grab the tubing.  Do not remove the fitting.  When 
made up properly, it should be leak-tight.

3.  Turn the output pressure regulating knob clockwise until the gauge registers 

345 KPA (50 psi).

4.  Allow five minutes for equilibration, then turn the regulating knob all the way 

counterclockwise.

5.  Observe the needle of the output pressure gauge for 15 minutes.  There will  

be a slight initial drop, but if it doesn’t move after that, consider that all the 
connections are tight.

6.  If necessary, use an electronic leak detector to locate any leaks.  If a leak  

detector is not available, tighten all the fittings (including the output  
pressure gauge), and repressurize the system for another test.

7.  Uncap the outlet tube of the purifier and purge the system for 15 to 30 minutes 

at 60 to 80 mL/min to eliminate air from the purifier getter material.

Column Connection

To prevent detector contamination, it is strongly  
recommended that the column be disconnected  
from the detector during column bake-out procedures.

Referenced mode

In the referenced mode, the column is connected to the Channel A inlet, and the 
carrier gas stream is split and used as a reference in channel B.  The gas flow rate 
from both channels must be the same (flow balanced).  This mode of operation 
provides the best baseline stability and the least background noise.

Unreferenced mode

In the unreferenced mode, Channels A and B are used independently.  One column 
connects to the Channel A inlet, and the other to Channel B.  The carrier gas must 
be the same for both channels.  It is also possible to use only one channel with 
the other capped off, as long as the filament temperature control of the unused 
channel is set to minimum.

The unreferenced mode has certain limitations.  There is a possibility of detector 
cross-talk (interference) if compound concentrations exceed 1%.  Also, baseline 
drift and background noise are greater compared with the referenced mode.

EZR21

Installation

Содержание Vici TCD-3











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды