Valco baby Vici TCD-3 Скачать руководство пользователя страница 3

Страница: 3 / 42

Table of Contents

Introduction
Description .......................................................................................................................................... 1

Operating Principle........................................................................................................................... 1

Operational Overview ..................................................................................................................... 2

Safety Notes and Information ....................................................................................................... 3

Symbols ...................................................................................................................................... 3

Installation Category ............................................................................................................. 3

Safety .......................................................................................................................................... 3
Maintenance............................................................................................................................. 3

Components of the Detector System ........................................................................................ 4

Description of Controls, Indicators, and Connectors ............................................................ 5

Hardware Specifications ................................................................................................................. 6

System Requirements ............................................................................................................................... 7

Components Not Included with the Detector System ........................................................ 7

PC System Requirements ............................................................................................................... 7

System Purity ...................................................................................................................................... 7

GC Column Selection ....................................................................................................................... 7

Recommended Carrier Gas Purifiers .......................................................................................... 7

Carrier Gas Selection ........................................................................................................................ 8

Installation .................................................................................................................................................... 9

General Precautions ......................................................................................................................... 9

Component Dimensions................................................................................................................. 9

Detector Mounting .........................................................................................................................10

Vertical Mounting .................................................................................................................10

Horizontal Mounting ...........................................................................................................11

Gas Connections ..............................................................................................................................11

Installing and Purging the Gas Regulator ...............................................................................11

Installing and Purging a Purifer ..................................................................................................13

Column Connection .......................................................................................................................13

Referenced Mode .................................................................................................................13

Unreferenced Mode .............................................................................................................13

Packed Columns ....................................................................................................................14

Packed Columns with Swagelok®-type Female Nut ................................................14

Capillary Columns ................................................................................................................14

Testing for Leaks ..............................................................................................................................14

Cable Connections ..........................................................................................................................15

Heater and Filament Connections ..................................................................................15

Data Output Cable(s) ...........................................................................................................15

Serial Data Extension Cable ..............................................................................................15

Digital I/O Cable (optional) ...............................................................................................15

Power Calbe ............................................................................................................................15

Flow Rate Settings ..........................................................................................................................16

Installing the Graphical User Interface (GUI) Software ......................................................17

Establishing Communication ......................................................................................................17

Initial Bakeout and Equilibration ........................................................................................................19

Initial Conditioning .........................................................................................................................19

Temperature Settings ....................................................................................................................19

Balancing the Channels ................................................................................................................20

Содержание Vici TCD-3











































Результаты поиска

Содержание Vici TCD-3

Отзывы:

Бренды по названию

Популярные бренды

Valco baby Vici TCD-3, Инструкция по эксплуатации

Результаты поиска

Содержание Vici TCD-3

Отзывы:

Бренды по названию

Популярные бренды