manualshive.com logo in svg

Valco baby Vici TCD-3, Инструкция по эксплуатации

Поделиться
Скачать
Valco baby Vici TCD-3 Скачать руководство пользователя страница 10

6

4.  48 VDC

 connector 

The 4' cable from the 48 VDC power supply is plugged into this connector.

5.  RS 232

 connector 

Connect the controller to a PC via a standard DE9 extension cable (M-F).  This  
DE-9F connector conforms to EIA-232C standard pin-outs for a DCE device.

6.  DIGITAL I/O

 connector 

This connector provides three digital inputs and one digital output signal.   

Refer to “Appendix A: Digital I/O Control” on page 30.

7. HEATERS

 connector 

The heater cable from the detector mates with this connector. 

8. FILAMENTS

 connector 

The filaments cable from the detector mates with this connector. 

NOTE:  The HEATER and FILAMENTS connectors carry 
live voltages, and should only be used with equipment 
having no accessible live parts.

9.  ANALOG OUT

 connector 

This is normally connected to a data acquisition system or other recording device. 
For convenience, full-scale 0 - 1V and 0 - 10V outputs are provided, with an internal 
signal reference (-) at zero volts. For best noise performance, the shield (earth) 
and signal reference (-) should not be connected together.

Hardware Specifications

Parameter

Minimum

Nominal

Maximum

Units

Notes

Controller input voltage

44

48

52

V

 

Controller input current

0.1

 

1.5

A

Vin = 48 Vdc

Input fusing

 

2.0

 

A

Internal fuse, time delay type

Operating Temperature

-10

 

40

°C

Storage Temperature

-25

 

70

°C

 

Humidity

 0

 

95

%

Non-condensing

Controller weight

 

1.4

 

lbs. 

Without cables

Detector cell weight

 

3.0

 

lbs.

Standard configuration

Detector temperature

 ambient

 

300

°C

 

Detector pressure

1

 

1000

psi

Working pressure

Heater power

 

 

60

W

Vin = 48 Vdc

Analog output (1V)

-1.2

 

1.2

V

1V output signal

Analog output (10V)

-12

 

12

V

10V output signal

Analog out impedance

 

100

 

Ω

 

Digital inputs

-0.5

 

5.5

V

Internal 4.7k

Ω

 pull-up to +5V

Digital input, logic high

2.0

V

Minimum logic-high threshold

Digital input, logic low

0.8

V

Maximum logic-low threshold

Digital output, voltage

-50

 

50

V

Open contacts; maximum volts

Digital output, current

-0.5

 

0.5

A

Continuous current rating

Table 3:

  Hardware specifications

Introduction

Содержание Vici TCD-3











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды