Vaisala Veriteq viewLinc 3.6 Скачать руководство пользователя страница 20

Страница: 20 / 122

Chapter 1: Getting Started

2011 Vaisala Canada Inc

Insert the Digi driver CD into viewLinc Server.

The Digi Device Setup Wizard launches automatically.

Click

Next

Select the device that matches the MAC address from

the bottom of your Digi device. Click

Next.

Note:

If your device is on a different subnet from the

server, you will need to know the IP address of

the Digi device and launch the RealPort installer

on the Digi Driver CD.

Configuring RealPort and Installing Drivers

In the Configure Network Settings screen, enter an IP

address (provided by your IT department). Click

Next

two

times.

In the Configure RealPort Settings screen, select “Install

Digi RealPort on this computer”. Click

Next

Click

Next

again. The settings are saved.

Click

Finish

Repeat

Installing Digi Drivers

for each Digi device.

Method 3: Using USB Port

You can also connect data loggers directly to PCs using a

USB Port, as shown in Figure 3.

Figure 3: Overview of viewLinc system using USB port to connect
loggers

Содержание Veriteq viewLinc 3.6



























































































































Результаты поиска

Содержание Veriteq viewLinc 3.6

Отзывы:

Похожие инструкции для Veriteq viewLinc 3.6

Бренды по названию

Популярные бренды

Vaisala Veriteq viewLinc 3.6, Руководство администратора

Результаты поиска

Содержание Veriteq viewLinc 3.6

Отзывы:

Похожие инструкции для Veriteq viewLinc 3.6

Бренды по названию

Популярные бренды