Vaisala Veriteq viewLinc 3.6 Скачать руководство пользователя страница 18

Страница: 18 / 122

Chapter 1: Getting Started

2011 Vaisala Canada Inc

Power Over Ethernet, you do not need to con-

nect to a power supply.

For more information about installing vNet devices, refer to

the vNet User Guide.

Installing Vaisala Veriteq Drivers

This section covers installing the drivers for vNet devices to

connect Vaisala Veriteq loggers to the network using an

Ethernet connection. Repeat all of these steps for each vNet

device you want to use.

Discovering the vNet Device

Obtain a reserved (recommended) or static IP address

for your vNet device from your IT department. If your

networking policy requires you to reserve IP addresses

using DHCP, see www.vaisala.com/veriteq for

instructions.

Insert the vNet Device driver CD into the viewLinc

Server.

The Device Setup Wizard launches automatically. Click

Next

Select the device that matches the MAC address from

the side of your vNet device, then click

Next.

Note:

If your device is on a different subnet from the

server, you will need to know the IP address

of the vNet device and launch the RealPort-

Setup.exe installer from the RealPort folder on

the vNet Device Drivers CD.

Configuring RealPort and Installing Drivers

In the Configure Network Settings screen, enter an IP

address (provided by your IT department). Click

Next

two

times.

In the Configure RealPort Settings screen, select

Install

RealPort on this computer

, then click

Next

Click

Next

again. The settings are saved.

Click

Finish

Repeat

Installing Vaisala Veriteq Drivers

for each vNet

device.

Содержание Veriteq viewLinc 3.6



























































































































Результаты поиска

Содержание Veriteq viewLinc 3.6

Отзывы:

Vaisala Veriteq viewLinc 3.6, Руководство администратора, Страница: 18 / 122

Результаты поиска

Содержание Veriteq viewLinc 3.6

Отзывы: