128
CARRIER COMFORT NETWORK
®
INTERFACE —
The 48/50A Series units can be connected to the CCN inter-
face if desired. The communication bus wiring is a shielded, 3-
conductor cable with drain wire and is field supplied and
installed. See the Installation Instructions for wiring informa-
tion. The system elements are connected to the communication
bus in a daisy chain arrangement. The positive pin of each sys-
tem element communication connector must be wired to the
positive pins of the system elements on either side of it. This is
also required for the negative and signal ground pins of each
system element. Wiring connections for CCN should be made
at TB3. See Fig. 39. Consult the CCN Contractor’s Manual for
further information.
NOTE: Conductors and drain wire must be 20-AWG
(American Wire Gage) minimum stranded, tinned copper.
Individual conductors must be insulated with PVC, PVC/
nylon, vinyl, Teflon*, or polyethylene. An aluminum/polyester
100% foil shield and an outer jacket of PVC, PVC/nylon,
chrome vinyl, or Teflon with a minimum operating tempera-
ture range of –20°C to 60°C is required.
It is important when connecting to a CCN communication
bus that a color-coding scheme be used for the entire network
to simplify the installation. It is recommended that red be used
for the signal positive, black for the signal negative and white
for the signal ground. Use a similar scheme for cables contain-
ing different colored wires.
At each system element, the shields of its communication
bus cables must be tied together. If the communication bus is en-
tirely within one building, the resulting continuous shield must
be connected to a ground at one point only. If the
communication bus cable exits from one building and enters an-
other, the shields must be connected to grounds at the lightning
suppressor in each building where the cable enters or exits the
building (one point per building only).
To connect the unit to the network:
1. Turn off power to the control box.
2. Cut the CCN wire and strip the ends of the red (+), white
(ground), and black (–) conductors. (Substitute appropri-
ate colors for different colored cables.)
3. Connect the red wire to (+) terminal on TB3 of the plug,
the white wire to COM terminal, and the black wire to the
(–) terminal.
4. The RJ14 CCN connector on TB3 can also be used, but is
only intended for temporary connection (for example, a
laptop computer running Service Tool).
5. Restore power to unit.
R
u
n
S
t
a
t
us
S
ervice
Te
s
t
Temper
a
t
u
re
s
Pre
ssu
re
s
S
etpoin
t
s
Inp
u
t
s
O
u
tp
u
t
s
Config
u
r
a
tion
Time Clo
ck
Oper
a
ting Mod
e
s
Al
a
rm
s
E NTE
R
E
S
C
M O D
E
Al
a
rm
S
t
a
t
us
TIME
EWT
LWT
S
ETP
1 2 . 5
8
5 4 . 6
F
4 4 . 1
F
4 4 . 0
F
N A V
I G A
T O R
Co m
f o r t
Li n k
Fig. 38 — Accessory Navigator Display
IMPORTANT: A shorted CCN bus cable will prevent
some routines from running and may prevent the unit
from starting. If abnormal conditions occur, unplug the
connector. If conditions return to normal, check the
CCN connector and cable. Run new cable if necessary.
A short in one section of the bus can cause problems
with all system elements on the bus.
* Teflon is a registered trademark of DuPont.
Содержание Carrier Weathermaker 48A2
